VS 8-2/VS 8-4

Regarding a vacuum switch valve and a vacuum release valve If a non-vacuum valve is installed in the middle of piping system having a vacuum, the vacuum condition will not be maintained. Use a valve designed for use under vacuum condition. 10.

Digital Flow Switches

such as a voltmeter.

MY1

Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if a surge is applied repeatedly. When directly driving a load that generates surge, such as a relay or solenoid valve, use a switch with a built-in surge absorbing element. 8.

NCQ8

B A HS HS B A B A 075, 106 HS B A B A 150, 200, 250, 300, 400 Note) Figures in the table below are references for auto switch mounting positions in the stroke end detection.

Rotary Table/

When a load, such as a relay or solenoid valve, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.

CG5-S

Mineral oil A C A A A A 18 Sodium hypochlorite (2%, Room temperature) A C A D D B 19 Sodium chloride A A A A B 20 Carbon dioxide A A A A A A 21 Natural gas A A A A A A 22 Boric acid A B A D A B 23 Unless noted otherwise, the solution concentration is in a saturated state.

Compressed Air Cleaning Filter Series

A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty.

CY1F

Operate the piston within a range such that collision damage will not occur at the stroke end. 5. Consider a possible drop in operating pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.

Magnetically Coupled Rodless Cylinder

(The switch will stay ON all the time.) 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 5m or longer. 7. Do not use a load that generates surge voltage. If driving a load such as a relay that generates a surge voltage, use a contact protection box.

Intrinsically Safe Valve

The solenoid must be connected to a safety barrier located in a non-hazardous area.

AS

AS22;1F-01-23(S)A 3.2 7.2 9 (9) AS22;1F-01-04(S)A 4 8.2 19.1 26.1 (26) 13.3 13 AS22;1F-01-06(S)A 19.1 6 1/8 10.4 11.6 30.6 29.2 27.5 26.1 10 (9) (12.7) AS22;1F-01-08(S)A 8 13.2 22.4 29.4 (29.3) 14.2 11 (10) AS22;1F-01-10(S)A 10 15.9 25.3 32.3 (32.2) 15.6 12 (11) AS22;1F-02-23(S)A 3.2 7.2 20.9 30 (30.3) AS22;1F-02-04(S)A 4 8.2 13.3 18 (19) 17 AS22;1F-02-06(S)A 22.6 6 1/4 10.4 12.6 23.4 32.5

VDW

A Common Specifications N.C.

MY2

If driving a load such as a relay that generates a surge voltage, use a contact protection box. Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if the surge is applied repeatedly.

Pilot Operated

0 A !3 !2 !1 o i t !0 !3 !2 !1 o i e t !0 A A e u w y q B C P2 P1 OUT IN P1 w y u B q w y u B q P2 OUT C C IN VXD2272/2382/2392 (32A to 50A) VXD2270/2380/2390 (32A to 50A) !4 !5 !3 !1 i t e !2 !0 A r u B y q !3 !2 !1 i t e o !0 A r u B y q w o w C C Operation When the coil !

2–4

Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if a surge is applied repeatedly. When directly driving a load which generates surge, such as a relay or solenoid valve, use a type of switch with a built-in surge absorbing element. 8.

Compact Type

Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3. A bumper at the end of the bumper bolt is replaceable. In case a missing bumper, or a bumper has a permanent settling, use a following part numbers for ordering.

48

7 u A A A-A (LEL25LT-n) A-A (LEL25MT-n) !9 !9 t @0 @1 !0 !6 !8 !5 o Component Parts Description No.

Smooth Cylinder

Vertical actuation (Speed control) I II P2 W A P1 a B A P0 P0 a A W (1) Basically, meter-out control is used. Combine meter-in control to reduce sudden movement. (1) Basically, meter-out control is used.

Electric Actuator

To prevent danger and damage due to a breakdown or malfunction of these products, which may occur at a certain probability, a backup system should be arranged in advance by using a multiple-layered structure or by making a fail-safe equipment design, etc. 13. Avoid heat radiation from strong heat sources, such as direct sunlight or a hot furnace.

CU

A + A' A' w After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved. A A' A' e When air is supplied for the piston extension, the check valve opens and the piston extends with no delay.