Wedge Cam Operation Gripper Series MHK2

For setting the holding force to be at least 20 times the work weight: Required holding force= 0.17kg 20 9.8m/s2 = 33N Holding point L=40mm Operating pressure: 0.5 MPa (72.5 psi) Holding Point I. D. Holding O. D.

3 Port Solenoid Valve SYJ300/500/700 Series

Common exhaust(pilot and main valve)type Pilot exhaust Not required Lubrication Free Mounting position 150/30 Impact / Vibration resistance m/s2 Dust proof Protection structure Base mounted type Solenoid Specifications Grommet (G), E(H), L type plug connector (L), M type plug connector (M) Electrical entry Coil rated voltage V DC 24, 12, 6, 5, 3 Internal pilot AC 50/60Hz 100, 110, 200, 220

9.8

in X, Y, Z directions for 2 hours each (De-energized) Vibration resistance 100 m/s2 in X, Y, Z directions 3 times each (De-energized) Impact resistance 2% F.S.

mlu

Do not drop, bump or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.

Rotary Table

Warning Do not drop, bump or apply excessive impacts (300m/s2 or more for reed auto switches and 1000m/s2 or more for solid state auto switches) while handling. Although the body of the auto switch may not be damaged, the inside of the auto switch could be damaged and cause malfunction. 2. Observe the proper tightening torque for mounting an auto switch.

0.01

EXH port P1 SUP port Sensor S1 S3 S2 S4 P2 Detection port S1, S2: Fix orifice S3: Variable orifice (adjusted by setting dial) S4: Detection nozzle 868 A Air Catch Sensor Series ISA2 Wiring Individual wiring Centralized wiring Terminal block 1: Brown 2: NC 3 0 1 2 3 4 Brown Blue Black DC (+) NC DC () OUT ZSE30 ISE30 OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 6 9 3: Blue DC () NC DC (+) OUT 6 ZSE40 ISE40

ITVH

(Error number 5) Vs : Power supply 24 VDC A : Input signal 4 to 20 mA DC 0 to 20 mA DC Vs : Power supply 24 VDC Vin : Input signal 0 to 5 VDC 0 to 10 VDC 4 points preset input type Brown Blue S1 White Vs Black S2 Vs: Power supply 24 VDC (Negative common) One of the preset pressures P1 through P4 is selected by the ON/OFF combination of S1 and S2.

Series 10-SYJ300/500/700 Rubber Seal 3 Port Solenoid Valve

pressure range (MPa) 0.15 to 0.7 Internal pilot Ambient and fluid temperature (C) Response time ms (at 0.5 MPa) Note 1) 10 to 50 (No freezing. ) 15 or less Max. operating frequency (Hz) 10 Non-locking push type, push-turn locking slotted type, push-turn locking lever type Manual override (Manual operation) Pilot exhaust method Lubrication Mounting orientation Impact/Vibration resistance (m/s2

Possible to transfer a workpiece at low-speed.

Inertial load: Ta Ta = I 2 = [rad/s2] t2 Necessary torque: T T = Ta x 10 2 x = 0.003896 x x 10 = 0.015 [Nm] 42 (t is calculated with 2s per 90.) Even for resistance load, when the load is rotated, necessary torque calculated from inertial load shall be added.

[Option] 3 Port Solenoid Valve Direct Operated Poppet Type VT317 Series Rubber Seal

Lubrication Manual override Impact/Vibration resistance (2) Enclosure VV061 Non-locking push type 150/50 m/s2 VT325-C VV100 Dustproof Note 1) Based on dynamic performance test, JIS B 8419: 2010.

Compact Cylinder with Air Cushion

Do not drop, bump or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.

When the LEF is ordered with the controller, initial data of the actuator is preset in the controller allowing start-up in a short time with the in.easy modein..Body size: 16, 25, 32, 40, Ball screw drive , Applicable stroke range: 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000, 2 types of motors: servo motor ball screw drive or step motor belt drive , Controller mounting: screw or DIN

When the LEF is ordered with the controller, initial data of the actuator is preset in the controller allowing start-up in a short time with the in.easy modein..Body size: 16, 25, 32, 40, Ball screw drive , Applicable stroke range: 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000, 2 types of motors: servo motor ball screw drive or step motor belt drive , Controller mounting: screw or DIN

This is a legacy product. Please contact us for the latest version.sales@ocaire.com

Style: Nozzle, Connection Size: 06 (R 3/4), Nozzle Diameter: 800 (Ø8)

Style: Nozzle, Connection Size: 10 (R 1), Nozzle Diameter: 800 (Ø8)

Cooling Capacity: 008 (800 W), Power Supply: W5 (100 to 240 VAC), Pipe Thread: N (NPT), Feet: None, Flow switch: F (w/Flow Switch)

Cooling Capacity: 008 (800 W), Power Supply: W5 (100 to 240 VAC), Pipe Thread: N (NPT), Feet: None, Flow switch: F (w/Flow Switch), Tank with Diagonal Fill Port: Nil (Standard Fill Port), High-pressure pump: P (High Pressure Pump Mounted)

Cooling Capacity: 008 (800 W), Power Supply: W5 (100 to 240 VAC), Pipe Thread: N (NPT), Feet: None, Flow switch: None, Tank with Diagonal Fill Port: Nil (Standard Fill Port), High-pressure pump: P (High Pressure Pump Mounted)

Cooling Capacity: 008 (800 W), Power Supply: W5 (100 to 240 VAC), Pipe Thread: N (NPT)