DC DE DO 4 x DR DU DL DA DU With Rubber Bumper [mm] [mm] Bore size Z Part no.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not use the ionizer in locations subject to sudden temperature changes even if the ambient temperature range is within the specified limits, as condensation may result. 2. Do not use this product in an enclosed space. Conduct a regular maintenance to see if the product is run having a disorder.
Wrapping of sealant tape When screwing together pipes and fittings, etc., be certain that chips from the pipe threads and sealant material do not get inside the piping. Also, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads. Operating Environment Warning 1. Do not use in environments where there is a danger of corrosion.
Do not disassemble or modify the main unit. Operating Environment Warning Caution 1. Do not use in the following environments, as this can cause damage and reduced performance. 1. Do not step on or place heavy objects on the unit. 1. Locations with an atmosphere of corrosive gases, organic solvents or chemical solutions, and locations where there may be contact with the same. 2.
Possible to use in vacuum or under low pressures External pilot type Vacuum: Up to 101.2 kPa Low pressure: 0 to 0.2 MPa Free mounting orientation 04 4 5 1 VP3 A G 1 SY SYJ Thread type Series VP 3 port solenoid valve Rc G NPT NPTF T N F Nil VK Number of solenoids VZ Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local
Symbol 01 02 03 04 06 Class 3 Class 2 Port size 1/8 (6A) 1/4 (8A) 3/8 (10A) 1/2 (15A) 3/4 (20A) Class 4 Electrical entry C Conduit G Grommet Orifice size Symbol 2 3 4 5 7 10 Class 3 Class 2 Orifice diameter Class 4 2mm 3mm 4mm 5mm 7mm 10mm D -DIN connector DL -DIN connector with light DO-For DIN connector (without connector) T -With conduit terminal TL-With conduit terminal/light Note) Note
Valve model Port size VCL2 VCW20-12-01 1/8, 1/4 34 40 25 30 12.8 12.8 5 4.5 6 13 VCW30-12-02 1/4, 3/8 42 52 30 40 19 19 6 5.5 7 19 VCL3 VCW30-12-04 1/2 48 56 36 44 23 23 6 5.5 7 23 VCW40-12-02 1/4, 3/8 42 52 30 40 23 23 6 5.5 7 19 VCW30-12-04 VCL4 1/2 48 56 36 44 23 23 6 5.5 7 23 VCW40-12-06 3/4 56 65 44 53 28.2 28.2 6 5.5 7 26 Bracket material: Stainless steel 3 Series VCL Direct Operated
Do not use compressed air which contains chemicals, organic solvents or corrosive gases. Do not use compressed air containing chemicals, organic solvents, salt or corrosive gases, as this can cause damage and reduced performance, etc. 3. Operating pressure range The operating pressure range is determined by the equipment being used.
Do not disassemble or perform any conversion work on flow switches. 4.
Do not touch the span calibration trimmer except when performing span calibration. Touching the trimmer may cause generation of an error in the measured pressure. Also do not turn it too hard (0.3 Nm or less) or press it too hard (5 N or less). 7. Use a soft cloth to wipe the blot off of the body.
Do not use two wire sensors.
Do not touch the span calibration trimmer except when performing span calibration. Touching the trimmer may cause generation of an error in the measured pressure. Also do not turn it too hard (0.3 Nm or less) or press it too hard (5 N or less). 7. Use a soft cloth to wipe the blot off of the body.
Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system. 1 L+ Brown 18 to 30 VDC 2 N.C.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
Do not use liquids that will cause the wetted sealant to swell.
Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
Do not use in a location having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. Do not use in locations where radiated heat will be received from nearby heat sources. Maintenance Warning 1. Maintenance should be performed in accordance with the procedures in the Operation Manual.