VT307 Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). Also, since there is a breathing port for the armature in the manual override part, do not allow accumulation of dust and/or other foreign materials to block bleed port.
How to Order KQ2 H 05 S 02 With thread seal One-touch fittings Nil Without seal S With thread seal Applicable tubing O.D.
Do not connect the white wire of the sensor to . View A Terminal block number 4 3 2 1 1 2 3 4 5 6 7 8 8 7 6 5 20 For Water Digital Flow Switch/High Temperature Fluid Type Series PF2W Refer to www.poweraire.com for details of products compatible with overseas standards.
Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Bracket mounting Mount the bracket using the mounting screws supplied. The required tightening torque is 0.420.04 Nm.
Please prepare according to 3.2 Connected explanation.In order to avoid malfunction, do not connect to any place other than those shown in 3.2 Connected explanation.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. A protective cover, etc. should be used to shield valves from direct sunlight. 5.
Do not use valves where there is direct contact with, or in atmospheres of, corrosive gases, chemicals, salt water, water or steam. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. Confirm the specifications for each series. 4. A protective cover should be used to shield valves from direct sunlight. 5.
Do not perform unlocking while an external force such as a load or spring force is being applied. This is very dangerous because the cylinder will move suddenly.
Do not use for intermediate cylinder stops. This cylinder is designed for locking against inadvertent movement from a stationary condition. Do not perform intermediate stops while the cylinder is operating, as this will shorten its service life. 2. Select the correct locking direction, as this cylinder does not generate holding force opposite to the locking direction.
Do not unlock the cylinder while an external force such as a load or spring force is applied. This is very dangerous because the cylinder will move suddenly.
Prevention of electric shocks and fire Do not operate the switch with wet hands. Also, do not operate the thermo-con when water is present on its exterior surface. 2. Action in the case of error If any error such as an abnormal sound, smoke, or bad odor occurs, cut off the power at once, and stop supplying and conveying fluid.
Do not cover the inlet and outlet vents.
Table (3) Additional Mass [g] 1 50 100 150 200 250 300 10 20 31 4 25 44 9 32 61 13 40 99 14 50 99 22 63 148 24 80 207 35 100 Bore size (mm) Additional mass per 50 mm of stroke Switch magnet 20 4 Cylinder stroke (mm) Do not apply a lateral load over the allowable range to the rod end when it is mounted horizontally.
Caution Do not apply a load that is 50% or more of the theoretical output.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. EX9-PE1 power input connector No.1 M12 5-pin plug B-code Element No.
Do not use with pressure or temperature beyond the specification range.
Do not use two cylinders facing one another horizontally or vertically in such a way that their piston rods strike each other. 8. When the cylinder head side contains hydraulic fluid or is in a normally pressurized condition, the applied load must not be allowed to strike the piston rod end.
(Including band and screw) Operating Range Bore size (mm) Bore size (mm) Auto switch model Auto switch model 20 25 32 40 50 20 25 32 40 50 D-C7/C8 D-H7 D-B5/B6 D-G5/K5 D-B7/B8 D-G7/K7 D-B7/B80 BMA2 -025 BMA2 -032 BMA2 -040 BMA2 -050 BMA2 -020 10 8 10 9 10 D-B73C/B80C D-C7/C80 BA -32 BA -04 BA -05 BA -01 BA -02 10 8 10 9 10 D-C73C/C80C D-B5/B64 BM1 -01 BM1 -02 BM1 -32 BM1 -04 BM1 -05 10 8
BA -32 BA -04 BM1 -01 BM1 -02 BM1 -32 BM1 -04 Intermediate strokes and short strokes other than the above are produced upon receipt of order.