3 Port Solenoid Valve/ Allowable voltage uctuation 10% Power consumption 0.45 W Surge voltage suppressor Varistor Indicator LED Manufacturer OMRON Rockwell Automation Electrical wiring G1/2, M12 connector M12 connector Contact resistance 25 m or less 50 m or less Min. applicable load 5 VDC, 1 mA (Load resistance) 5 VDC, 5 mA (Load resistance) Max. voltage 24 VDC Max. load current 50 mA Max. load inductance 0.5
Power supply voltage 24 VDC (Including ripple from 22 to 26 VDC) Power consumption Approximately 29 W Output current range 0 to 1 A Impedance of electro-pneumatic proportional valve 13 to 18.5 (1 A F.S.)
, 600 or less with 24 VDC Power supply voltage 12 to 24 VDC (Ripple 10% or less) Current consumption 20 mA or less (Without load) Enclosure IP65 Operating temperature range Operating: 0 to 50C, Stored: 25 to 85C in stock (No freezing or condensation) Environmental resistance Voltage resistance 1000 VAC for 1 min between external terminals and case Insulation resistance 50 M or more (500
ZSP ISA2 Fig. (2) Equivalent circuit of an NPN switch with the output off PLC Low level 12 to 24 [VDC] IS Main circuit of switch Max. 80 [mA] Max. 30 [V] ZSM Load PF2 Current flows. Load is powered. IF Fig. (3) Equivalent circuit of an NPN switch with the output on Data PNP 12 to 24 [VDC] Fig. (4) shows an example of a PNP switch.
voltage 24 VDC type: 0.12 A or less Power supply voltage 1 2 to 1 5 VDC type: 0.1 8 A or less Input signal Current tvDe Nda2r 4 to 20 mA. 0 to 20 mA (Sink tvoe) Voltage type 0 to 5 VDC. 0 to l0 VDC Presel inDut 4 ooints Current type 250 o or less Voltage type AoDrox. 6.5 kQ Presel inpul ADotox.2.7 ket Straight type Right angle type Inpul impedance H Analog output 1 lo 5 VDC (Load impedance
less 50 mA, 40 mA, 20 mA IC circuit, Relay, PLC No Reed auto switch D-A90 D-M9B, D-F8B D-M9N, D-F8N 2-wire 3-wire 24 VDC relay, PLC 24 VDC relay, PLC Solid state auto switch Yes 24 VDC (10 to 28 VDC) 24 VDC (4.5 to 28 VDC) Yes 2.5 to 40 mA 40 mA or less Refer to page 920 for the applicable auto switch list. 909 Rotary Table MSQ 1122Specifications Suction Flow Rate of Vacuum Suction Type
A 24 VDC 4 15A N.C. F C37 1/2 15 G Stainless steel B 100 VAC Grommet With surge voltage suppressor C 110 VAC 5 20A N.C. H C37 3/4 20 J Stainless steel D 200 VAC E 230 VAC 6 25A N.C.
supply cable (For 24 VDC wiring) Conductor nominal cross section 0.15 mm2 Insulator O.D.
Proper use of the seal cap enables the enclosure to achieve IP67 specification. 25 EX## OMS1015-A Specification Specifications Model EX600-ED2EX600-ED3Power connector M12 (5 pin) Plug 7/8 inch (5 pin) Plug specifications Power Power supply (Control and input) 24 VDC, 10%, Class2, 2 A 24 VDC, 10%, 8 A Power supply (Output) 24 VDC, +10/-5%, Class2, 2 A 24 VDC, +10/-5%, 8 A Enclosure IP67 (With
Flow switch Blue (DC COM) Brown (24 VDC) Terminal No. 14 Brown (24 VDC) 6 Terminal No. Flow switch 5 Terminal No. Blue (DC COM) 11 Terminal No. Black (Output 1) 3 Terminal No. Black (Output 1) Fig. 3-12 Wiring of the external switch (NPN open collector output) (example) Flow switch Blue (DC COM) Brown (24 VDC) Brown (24 VDC) Terminal No. 14 Terminal No.
Flow switch Blue (DC COM) Brown (24 VDC) Terminal No. 14 Brown (24 VDC) 6 Terminal No. Flow switch 5 Terminal No. Blue (DC COM) 11 Terminal No. Black (Output 1) 3 Terminal No.
Step motor (servo/24 VDC) and servo motor (24 VDC) specifications with the following model number are not compliant with UL Standards: Controller/Driver type: Without controller/driver (Nil). Individual actuators are not certified as UL Standards compliant products. 7.
insulation type 1 W DC (42 mA), 0.5 W DC (21 mA) (4) 24 VDC Power consumption (Current) 1 W DC (83 mA), 0.5 W DC (42 mA) (4) 1 (P) 5 (R1) 3 (R2) 1 (P) 5 (R1) 3 (R2) 12 VDC Metal seal Rubber seal Note 1) Use dry air to prevent condensation when operating at low temperatures.
Relay Circuit Example Open-collector Circuit Example DRIVER DRIVER 24 VDC +24 VIN 3.3 k +24 VIN 3.3 k 24 VDC /DEC, etc. /DEC, etc. Note: The 24 VDC external power supply capacity must be 50 mA minimum. The DRIVERs input circuit uses bidirectional photocoupler. Select either the sink circuit or the source circuit according to the specifications required for each machine.
Relay Circuit Example Open-collector Circuit Example DRIVER DRIVER 24 VDC +24 VIN 3.3 k +24 VIN 3.3 k 24 VDC /DEC, etc. /DEC, etc. Note: The 24 VDC external power supply capacity must be 50 mA minimum. The DRIVERs input circuit uses bidirectional photocoupler. Select either the sink circuit or the source circuit according to the specifications required for each machine.
(such as static electricity. (2) Check if the power supply voltage System error is in the range 24 VDC 10%. (Er0, 4, 6, 7, 8 or 9) is displayed. (2) Supply power in the range 24 VDC 10%. HHH is 6 displayed. (1) Reset applied pressure (1) Check that the pressure is not to a level within the set pressure range.
[Example] 10-SYJ3123-5M-M3 VJ3000-13-1 Rated voltage 5 port DC AC (50/60Hz) 5 6 V S R 1 2 3 4 24 VDC 12 VDC 6 VDC 5 VDC 3 VDC 100 VAC 200 VAC 110 VAC [115 VAC] 220 VAC [230 VAC] For type "W", DC voltage is only available.
Status indicator Yes on LCD screen Precision +/5% (0.5 VDC) Offset/gain Offset value: 0 to 0 VDC ELECTRICAL SPECIFICATIONS ENVIRONMENT Gain value: 0-10 = 0-255 Insulation 7 MOhms at 500 VDC These default values can be between connectors, acc. to changed in EN 60730 1 the Offset FB Safety class II T emp. dependent derating =/3 LSB Earthing None Protection IP20 Certifications CE, UL/cUL DC
to 24 VDC Load 6.8 k 12 VDC to 24 VDC (Black) OUT 1 ZSE ISE (Black) OUT 1 (White) OUT 2 (White) OUT 2 PSE (Blue) DC () (Blue) DC () Z I SE3 PS Z I SE1 2 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com ZSP ISA2 IS ZSE F/ISE --62(L)-(M) 50 60 50 60 ZSE F/ISE --70(L
12 VDC 7 240 VAC, Hz 50 60 Port size 50 60 Note 1) CE-compliant: Electrical entry is applicable only for the DIN terminal.