<br>Brackets are not available for older VHS and VHS400/500 series valves without locking holes. <br>New VHS series valves can be retrofitted with a bracket as well. Refer to the following for the part numbers of the brackets.<br><br>

<br>The silencer assembly can also be retrofitted to the valve. Refer to the following for the part number of the silencer assembly. <br>If an externally mounted silencer is preferred, order an AN series silencer, taking into consideration the thread size of the exhaust port.<br><br>

<br>In the fully closed state, no air is supplied to the outlet side. Adjust the switching timing of the valve by opening the needle valve a little. <br>Since it is dangerous if they pop out suddenly upon startup, the products are shipped with the needle valves in a fully closed state.<br><br>

<br>Note) The AL10-A is adjusted by opening the needle at the front of the product.<br><br>

<br>A 1000 cm2 tank type is available for standard AL30 to 60 series products. <br>Details on the 1000 cm2 tank type can be found here.<br><br>

<br>Note) Older tanks are subject to unexpected accidents due to internal corrosion caused by external damage or drainage. <br>Depending on the state of the old VBAT series air tank, consider replacing it with a new VBAT series air tank.

<br>This means that when air is not consumed on the outlet side, the outlet pressure becomes 1 MPa.<br>If 0.6 MPa air is constantly consumed at 1500 L/min (ANR) on the outlet side, the booster regulator will run continuously with almost no stopping time, resulting in a reduced service life.<br><br>

<br><br>

<br>②The pressure for driving may not be sufficiently obtained, resulting in the stopping of operation.<br>③ The operation frequency may increase and reduce the service life.

However, the fittings are in compliance with the following JIS standards: <br>For the KQ2 series: B8381-1 <br>For the KF series: B8381-2 <br>“No leakage occurs within 1 minute when the fitting fixed to a tube is underwater while pressurized for 5 minutes at both the max. operating pressure and 0.1 MPa.”

<br>In addition, the release buttons of the KQ2□-□N and KQ2□-□G have a different shape and dimensions from those of the KG series. <br>All KQ2□-□G series fittings with hexagonal sides have a V-shaped groove for discrimination.<br><br>

<br>Silicone, on the other hand, is an artificial compound made from silicon (the main component of siloxane). <br>Is it perhaps silicone that the user sees as a problem? <br>If so, there is only silicone used in the sealant of KQ2 and KQG2 series One-touch fittings. <br>However, silicone is not used in the fitting body or parts other than the seal.

<br>Note 2) Do not use combustible fluids, corrosive fluids, chemicals, poisonous gases, or seawater.<br>Note 3) Also, refer to the AP64 series check valve catalog, which can be found here. Be sure to check the precautions before considering this product.

<br>AN□02 series: It features 35 dB(A) noise reduction, and uses flame-resistant material (equivalent to UL-94 standard V-O) for the main body. Only 1/4, 3/8, and 1/2 port sizes are available. <br>(Reference 1) Standard AN series compact resin type silencer: 30 dB(A) noise reduction

<br>It removes oil mist contained in the exhaust and reduces exhaust noise of compressed air equipment at the same time.<br>Use this product when you want to both remove oil mist contained in the exhaust air from the solenoid valve and reduce the exhaust noise.<br><br>For selection, refer to the AMC series catalog, which can be found https://www.smcpneumatics.com/Part-Builder-Links_ep_2458-1.html?https://smccatalog.partbuilder.smcpneumatics.com/support/faq/en-jp/?ca_id=silencers-pressure-gauges&fa_id=10851