Valve Mounted Guide Cylinder Series MVGQ ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 Valve, Speed Controller, and Cylinder are formed into one unit. Easy piping wiring work for Valve, Speed Controller and Cylinder can be formed into one unit, furthe Easy piping wiring work for Valve, Speed Controller and Cylinder can be formed into one unit, further can be equipped into a more compact design.
Bore size (mm) Grease pack part no. 6 GR-S-005(5g) MXY6-PS Individual -X Set consists of 2 pieces of above 8 GR-S-010(10g) MXY8-PS !0, !
Be sure to take appropriate protective measures if the product is to be used in an environment where it will be constantly exposed to water or fluids other than water splash.
For bore size 20 or more, Rc, NPT and G ports can be selected.
Toggle Type Air Gripper Series MHT2 32, 40, 50, 63 RoHS New cylinder body allows small auto switches to be mounted on 4 surfaces. New cylinder body allows small auto switches to be mounted on 4 surfaces. Auto switch mounting rail removed. A round slot for mounting small auto switches is provided on 4 surfaces.
If frequent cleaning will be necessary, it can be suspended from the top panel of the tank. t If a fluid switch (built-in lead switch) or the like is used, it should be installed in a location where it will not be affected by magnetism from the separator. (Refer to the technical data sheet (FGX-TDT011) for information on magnetic fields.) Maintenance q Clean the separator regularly.
(The tightening torque should be about 2 to 3 Nm.) 5. Modification of the detecting position should be made in the condition of 3. 329
Ordering: Add the word CUJin front of the bolts to be used.
The expected performance and safety assurance of the equipment will be the responsibility of the person who has determined its compatibility with the product.
The tightening torque should be 0.5 to 1 Nm. As a rule, it should be turned about 90 beyond the point at which tightening can be felt. When auto switches D-M9/M9W/Y59 D-Y7, Y7W are used A B L Auto Switch Hysteresis When auto switches D-M9V/M9WV/Y69 D-Y7V, Y7WV are used Auto switches have hysteresis similar to micro switches.
The cylinder ports are designed so that a maximum speed 3000 mm/s can be obtained. However, it may not be possible to attain the desired speed in the case of short cylinder strokes. It may also be impossible to attain the desired speed due to restriction by component equipment (valves, speed control valves, piping, fitting, etc.).
MHY Position to be secured MHW Position where light turns ON -X MRHQ Fitting position 0.3 to 0.5 mm MA DNote 1) It is recommended that gripping of a workpiece be performed close to the center of the finger stroke.
Finally, all program debugging can be simply carried out from your own computer.
O~ 0.2 0.3 04 05 0.6 O~ 08 09 00 1000 2000 Auto drain Flow rate /min (ANR) Inlet pressure MPa (Float type normally open) AW4001-04 AW4001 -04 OOrain line should be Bmm or more and should be less than Sm. Be sure not to have any upward turns in the drain line which would prevent drainage. -0.25 H---''t' .:c ' +-+-t---+--r--.
Select the cylinder with bumper (O N") it cushion valVe is to be fuH yopened. Tie rods or piston assembly may be damaged if neither air cushion nor bumper is utilized.
However, be aware that its anti-corrosion performance is inferior to austenitic stainless steel. In particular, the finger might be rusted in an environment where water droplets are adhered to it due to dew condensation. 722 MHY2/MHW2 Series Specific Product Precautions 2 Be sure to read this before handling the products.
When the cylinder is used as mounted with a single side fixed or free (basic type, flange type), be careful not to apply vibration or impact to the cylinder body. A bending moment will be applied to the cylinder due to the vibration generated at the stroke end, and the cylinder may be damaged.
Description No Link, No Activity (Port2) LED is OFF 1 TX+ The EX500 range of units can be connected to open fieldbus (PROFINET) to realize the reduction of input or output device wiring and the distributed control system. One branch of manifold valves/input unit can be connected to 32 outputs/32 inputs.
Data may be lost. If the cylinder is operated vertically with heavy loads, measures must be taken to prevent rapid advancement of the piston rod when starting to operate in the downward direction.
Note 2) When exceeding the standard strokes, it will be out of warranty.