A Low speed supply Initial operation return stroke PA PP B Cylinder movement with fixed orifice 2 1(P) 1/2 PP > PA Pressure stroke D PP 2(A) 1 3(R) B A C PA PR (atmospheric pressure) ON A Time When 1/2 PP PA after the cylinder reaches , piston B fully opens and PA increases rapidly as shown from to and becomes the same pressure as PP.
Accessory None (Standard) With bracket (Except IDG1) Nil B Note) When symbol B is indicated, a bracket assembly with a part number shown in the table below is included as an accessory.
When the effective stroke of the absorber decreases as a result of stroke adjustment, the absorption capacity becomes extremely small.
When the effective stroke of the absorber decreases as a result of stroke adjustment, the absorption capacity becomes extremely small.
The advantages of this arrangement, using the air pressure within the valve to do the work, a r e d r a m a t i c a l l y r e d u c e d s i z e a n d p o w e r c o n s u m p t i o n o f t h e s o l e n o i d , a n d a f a s t e r response. The disadvantage is that this type of valve is incapable of operating without pressure applied as in a vacuum system.
Effect of back pressure when using a manifold Use caution when valves are used on a manifold, as actuator malfunction due to back-pressure may occur. Implement countermeasures in cases where there is a danger of this kind of malfunction. 3. Pressure Since valves are subject to air leakage, they cannot be used for applications such as holding pressure in a pressure vessel.
Note 2) 52-SY920 valve are not available with manifold as standard.
Blanking block assembly (VCA30, 40) VVCA 3 0 2A 00 3 4 Series VCA30 Series VCA40 This is used when a blanking block is mounted on a manifold as preparation for a planned valve installation.
Slide Locking Type (Manual type) (SQ2000 only) The manual override is locked by sliding it all the way to the pilot valve side (ON side) with a small flat head screwdriver or finger. Slide it to the fitting side (OFF side) to release it. In addition, it can also be used as a push type by using a screwdriver, etc., of 2 or less.
The length of the lead wires between the switch unit and contact protection box should be no more than 1m, and they should be placed as close together as possible. Tighten with a torque of 0.10 to 0.20Nm. As a rule, it should be turned about 90 past the point at which tightening can be felt.
This acceleration process can be achieved smoothly (as a sine function) by using a cushion spear on which a U-shaped groove is machined. The piston stops at the stroke end on rod side with smooth cushioning. Air flow which is switched by solenoid valve is reversed from the one indicated in the above 1. Start-up. 6. Reset 3.
This acceleration process can be achieved smoothly (as a sine function) by using a cushion spear on which a U-shaped groove is machined. The piston stops at the stroke end on rod side with smooth cushioning. Air flow which is switched by solenoid valve is reversed from the one indicated in the above 1. Start-up. 6. Reset 3.
IP8000-011-AG) Note 3) A is applied to approx 90cm3-capacity actuator. B is applied to approx 180cm3-capacity actuator. Note 4) Standard lever is not attached. Note 5) It is to be used together with A or B when tending to overshoot by the use of A or B. It is mounted to the body as a replacement of the standard compensation spring. Note 6) With terminal box, Non-explosion proof.
only 54 18 Clip B Stainless steel Snap ring Stainless steel 25, 32 only 55 19 Steel ball A Carbon steel Cushion seal A Urethane 56 20 Same as cushion seal A except for 20, 25 standard strokes Steel ball B Carbon steel 21 Cushion seal B Urethane 57 Tooth ring Stainless steel 22 Damper Urethane Cushion ring gasket A NBR 58 23 Same as cushion ring gasket A except for 20, 25 standard strokes
Evaporation thermometer V Dustproof filter provided as a standard accessory V All electrical components are located in the front of the product.
Also keep the manual in a place where it can be referred to as necessary. 3. Painting and coating Warnings or specifications printed or labeled on a product should not be erased, removed or covered up. Furthermore, please contact SMC before painting the resin parts, as this may cause adverse effects depending on the solvent. Adjustment Caution 1.
Note 2) Allowable rotating torque, and operating range when used as a lifter, are the same as MGPWL series.
Note 2) Model MGPL (Ball bushing bearing) cannot be used as a stopper. 20 12 10 0 10 20 30 Transfer speed (m/min) Bore Size 32 to 100/MGQM32 to 100 (Slide bearing) MGQM32 to 100 (Slide bearing) ~ = ~ = 1500 100 l l 1000 When selecting a model with a longer l dimension, be sure to choose a bore size which is sufficiently large. 900 80 800 700 Caution on handling Note 1) When using as a stopper
As a result, it is necessary for the customer to verify compliance with the EMC directive for the machinery and equipment as a whole. The actuator and controller are sold as a package. Confirm that the combination of the controller and actuator is correct.