Solid State Auto Switch Proper tightening torque The tightening torque of the M3 mounting screw must be 0.5 Nm (5.1 kgfcm). < D-S79, D-S7P, D-T79, D-T79C > 1. Auto switch mounting Loosen the cross recessed round head screw (2), and insert the arm of the auto switch. 2.
Model Thread size Tightening torque SX3000 M2 0.17 Nm SX5000 M3 0.8 Nm SX7000 M4 1.4 Nm 11 SX3000-OMM0002-B -12-SX3000-OMM0002-B -13SX3000-OMM0002-B TROUBLESHOOTING Should any trouble be found during operation, trace the source of the trouble in the following order and take corrective action.
Connection of fittings When screwing fittings into valves, tighten as follows. (1) Follow the procedures below when installing an SMC fitting, etc. 1) M3 After tightening the fitting by hand, use a wrench to tighten the fitting an additional approximately 1/4 turn.
Cross recessed round head screw for mounting the bottom bracket Square nut Bottom bracket Applicable torque IRV10(A):M3 0.320.03Nm IRV20(A):M4 0.760.05Nm 8 - Caution Handling (1) Reduce the set pressure to zero(atmospheric pressure) for removing the plug when additionally mount the pressure gauge and pressure switch. 1.For customers purchasing regulator with a pressure gauge or pressure switch
Tighten the FG terminal (M3 round head combination screw) firmly with a tightening torque of 0.3 Nm. Tighten the connector fixing screws (M2.5 slotted head screws) firmly with a tightening torque of 0.2 to 0.3 Nm. A. Dual power supplies B. Single power supply Figure 3 Figure 4 : Communication connector FG and FG terminal are connected inside the SI unit.
For HAA71522 series Power cord Terminal Insulated ring terminal Customer connection side Terminal screw : M3 Connector width :6.5mm Suitable wire :0.75mm2 For HAA37 series Customer connection side Terminal screw : M3.5 Connector width :8.3mm Suitable wire :0.75mm2 HAA Series 12 9 1)Terminal Assembly (Symbol: T) ATX-OM-F004E Air-Cooled Aftercooler 9.
Actuator mounting A Model Bolt size Maximum tightening torque [Nm] Amm) mm LEKFS16 M3 0.63 3.5 23.5 LEKFS25 M4 1.5 4.5 24 LEKFS32 M5 3.0 5.5 30 LEKFS40 M6 5.2 6.6 31 4. When mounting the actuator, leave a gap of 40mm or more to allow for bending of the actuator cable. 20 - 3.4 Precaution on maintenance Warning 1.
Mount with the set screws M3 size (2 pcs.) supplied for direct installation. The required tightening torque of the mounting screws is 0.5 to 0.7 Nm. Mounting with panel mount adapter Panel mount adapter + Front protective cover (Model: ZS-39-D) -15No.PS-OMM0005-J Removal and mounting on DIN rail It is necessary to prepare a DIN rail adapter for the mounting on the DIN rail.
VBA-OM-L007-E The elbow for silencer (option) can be used only for mounting a silencer OPERATION MANUAL VBA-M3 Handling Precautions to the exhaust port. Do not use it for the IN port and the OUT port. Prepare piping separately to exhaust remotely by connecting pipes to the exhaust port. To ensure safe and optimum operation, confirm the products specifications before use.
Every air cylinder intended for use or mounting in Japan, with the gauge pressure of 0.2 MPa or more and the cylinder internal capacity of 0.04 m3 and more, or with the cylinder inside diameter of 200 mm dia. or more and the stroke of more than 998 mm falls within the scope of the second class pressure vessel regulations.
Connection of fittings When screwing fittings into valves, tighten as follows. (1) Follow the procedures below when installing an SMC fitting, etc. 1) M3 types After tightening the fitting by hand, use a wrench to tighten the fitting an additional approximately 1/4 turn. As a reference value, tightening torque is 0.4 to 0.5Nm.
Connection of fittings When screwing fittings into valves, tighten as follows. (1) Follow the procedures below when installing an SMC fitting, etc. 1) M3 types After tightening the fitting by hand, use a wrench to tighten the fitting an additional approximately 1/4 turn.
(Applicable bolt size is M3) These grooves can be used for firmly fixing the tying bands of lead wires of the auto switch, etc., and also terminal boards, etc., to the main body of the cylinder. When the terminal block is fixed on a cylinder directly. 6 12. Piping 12-1. Attention in piping 1) Use clean air.
Mounting dimension on side face Size Bolt Tap depth Size Bolt 05 M4X0.7 5 Body tap Body through hole 1 M5X0.8 6 05 M4X0.7 M3 1 M5X0.8 M4 Piping Fig. (4) and Table (8) show port position and size. A port A port B port B port Side port Front port Fig.4 Port position 24 - Table 8. Port size .
50 63,CF114 80 Actuating type Normally closed (Pressurize to open , spring seal) Fluid Vacuum of inert gas Operating temperature oC 5 to 60 (High temperature type:5 to 150) Operating pressure Pa(abs) Atmospheric pressure to 1 x 10-6 Conductance l/s Note 2 5 14 45 80 160 200 Internal 1.3 x 10-10 for the standard material (FKM) at ambient temperatures , excluding gas permeation Leakage Pa m3
MB1 Bore size [mm] Thread size Pulling force Stroke [mm] 32 M2.5 x 0.45 x 25 L 4.9 N 2 40, 50, 63 M3 x 0.5 x 30 L 10 N 3 80, 100 M5 x 0.8 x 40 L 24.5 N 3 Before starting operation, supply air to side without locking mechanism as figure above, (or side without locking the piston rod for models with locking at both ends.) Otherwise, lock may not be released. (Refer to Release of lock.)
Note 50 63 32 40 Bore size (mm) Action Double acting Reed switch D-A7/A8 D-A73C/A80C D-A7H/A80H D-A79W Solid state switch D-F7/J79 D-F7V D-J79C D-F7W/J79W D-F7WV D-F7BAL/F78AVL D-F79F Fluid Air 0.1 to 0.6 MPa Operating pressure Switch mounting screw (M3 x 0.5 x 10l) Switch spacer Switch mounting nut. 5 to 60C Ambient and fluid temperature 32, 40 50, 63 BQ-2 Lubrication Not required 3 to
CL Bore size (mm) 20, 25, 32 40, 50, 63 80, 100 Thread size Pulling force Stroke (mm) MLGC M2.5 X 0.45 X 25l 4.9N 2 M3 X 0.5 X 3l 10N 3 CNA M5 X 0.8 X 40l 24.5N 3 Bolt should be detached under normal operation, otherwise it may cause malfunction of the locking feature. CB wThe lock piston is pushed further upward.
Step 3) Screw in the accessory unlocking bolt (hexagon socket headcap screw 32: M3 x 8l, 40: M4 x 8l, 50: M4 x 8l, 63: M5 x 10l). 1. Piping port position, switch rail position, and by-pass piping position can be selected by the part number. However, if there is an error in ordering and changes to the positions are required, please note the following. a.
Button head screw (M2.6 x 10) Tightening torque: 0.4 to 0.5Nm + Washer Brown lead wire Proximity switch Internal circuit Output Black lead wire Switch mounting bracket Hexagon nut Blue lead wire Thin head screw (M3 x 4) Tightening torque: 0.38 to 0.42Nm Round head screw (M2.5 x 5) GXL-8FU(B)(I) Tightening torque: 0.38 to 0.42Nm + Switch plate Spring washer Brown lead wire Switch plate Main