Multistage Ejector Connection Correct tightening thread torque (Nm) Rc1/8 7 to 9 Rc1/2 28 to 30 Rc3/4 28 to 30 Rc1 36 to 38 13 - Doc. no. ZL-OM00801 Piping to the Vacuum (V) Port (1) Allow a sufficient margin of tube length when piping, in order to prevent twisting, tensile, moment loads, vibration or impact being applied to the tubes and fittings.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Stations n: Stations Formula L1 = 20n + 11 L2 = 20n + 36 2 51 76 3 71 96 4 91 116 5 111 136 6 131 156 7 151 176 8 171 196 9 191 216 10 211 236 ( ): A port Rc 1/8 Symbol L1 L2 VT VP Common exhaust: VV3Z4-50 (Built-in One-touch fittings manifold) (G) (L
Therefore, the possible supply current to the sensor connected to the input block is 120 [mA] 84 [mA] = 36 [mA]. Use of low wattage type valves by minimizing the maximum number of simultaneous outputs, and low current consumption sensors (2-wire sensor, etc.) connected to the input block is recommended. Power Supply Safety Instructions Cable Safety Instructions Caution Caution 1.
.: GR-S-005 (5 g) 624 Angular Style Air Gripper Series MHC2-6/MHCA2-6 Dimensions MHC2-6 4 x M2 x 0.4 through Thread for attachment mounting Attachment mounting limiting range 16 11 2 x M3 x 0.5 through Prepared hole dia. 2.6 through 5 2.5 4.8 2 2 When closed 10 When open 30 4 2.5 14 20 12 4 6 10 0.05 MHZ Auto switch mounting groove dimensions MHF 36 +0.022 0 7H8 depth 1.5 MHL (48) MHR M3
Recommended tightening torque Unit: N m Thread size 1/8 1/4 3/8 1/2 3/4 1 Torque 7 to 9 12 to 14 22 to 24 28 to 30 28 to 30 36 to 38 (4) Before using an SMC fitting and S coupler, please refer to "Tightening the threaded portion of the connection thread" of the Fittings & Tubing Precautions. -5- (5) Do not apply torsion or bending moment other than the weight of the product itself.
A C D-F9 D-F9W D-M9 D-A93 D-A90 D-A96 D-F9V D-F9WV Bore size (mm) CXSJ15 to 32 B D A 15.5 25.5 31.5 39 40 49 D 9.5 7 0 3 5 5.5 C 9.5 19.5 25.5 33 34 43 B 6 9 11 11.5 B 0.5 3 10 13 15 15.5 D 7.5 5 2 5 7 7.5 A 15.5 25.5 31.5 39 40 49 A 19.5 29.5 35.5 43 44 53 C 11.5 21.5 27.5 35 36 45 D 5.5 3 4 7 9 9.5 D 8 5.5 1.5 4.5 6.5 7 B 6 9 11 11.5 B 0.5 3 10 13 15 15.5 C 13.5 23.5 29.5 37 38
Locating pin hole D x H (mm) Max.tightening torque ftlb (Nm) Model Depth l (mm) Bolt used 0.9 (1.2) MXW 8 5H9+0.03 depth 4.5 14.8 M3 x 0.5 0 1.5 (2.1) 5H9+0.03 depth 4.5 MXW12 19.2 M4 x 0.7 0 3.2 (4.4) MXW16 6H9+0.03 depth 5.5 21.5 M5 x 0.8 0 3.2 (4.4) MXW20 6H9+0.03 depth 5.5 30.5 M5 x 0.8 0 5.5 (7.4) MXW25 8H9+0.036 depth 9 36 M6 x 1 0 19
SY9000-36-A Wiring unit assembly 9 Caution Connector assembly Lead wire cover 10 11 12 SY9000-37Refer to page 84. SY9000-41-1 For 43P type (flat ribbon cable manifold) of series SY9000, lead wire cover to bundle lead wire of each solenoid is available. When double solenoid valves are added, order lead wire covers separately. Included with the DIN rail mount type.
or less 40 or less 36 or less 40 or less 36 or less 40 or less 40 or less 45 or less 50 or less 15 or less 20 or less 70 or less 80 or less 70 or less 80 or less 70 or less 80 or less 80 or less Single 2-position 5 (R1) 3 (R2) Double 1 (P) N.C.
It might cause mal function and Optimum operating position BLUE (-) GND Switch Main Circuit Most sensitive position 8.5 7-9-35 36 Made to Order Specifications: Solid State Switch With Pre-wired Connector For details about certified products conforming to international standards, visit us at www.smcworld.com.
Device state parameters (index 36) Readable device states are as follows.
(see P.36 Fig.2-1 and Fig.2-2 for circuit example) If the C24V is shut off when stopped, the operation will start when IN0 or IN1 turns ON after the stop is released. For closed center mode It operates according to the state of the IN0 and IN1 signals. If you do not restart the operation after releasing the stop, release the stop while both IN0 and IN1 are OFF.
(Unit: %) For the positioning operation, this value is ignored. 36 - Effective only for the pushing operation (when the value for the Pushing force is from 1to 100). This defines the movement speed during the pushing operation. If this Speed Minimum value to is too high, it may cause damage to the electric actuator or work piece due to Pushing speed impacts.
MONITOR2 11 12 13 SEL_MON1/2 SEL_MON1/2 14 IO_MON 15 16 WDT RWDT 17 18 19 20 21 22 Subcommand Subcommand 23 area area 24 25 26 27 28 29 8-36 8 MECHATROLINK-II Commands (2) OPTION Field Specifications The option field is used to add functions to a motion command.
0 3-5-80 81 5 Port Pilot Operated Solenoid Valve Rubber Seal, Plug-in/Non Plug-in Series VFR5000 Plug-in 2 position single/double, 3 position closed center/exhaust center/pressure center 0 1 2 position single: VFR510 -F(Z) 21 [25] 32 [39] 40 [40.5] 31 [36] 25 [24] 31 [36] 1 2 31 [41] 16 [19.5] 16 [19.5] EA P EB VK A B 32 [39] 40 [40.5] VZ 5-Rc 3/8, 1/2, 3/4 EA, EB port = Rc 1/2 in case of
F5P/J59/J51 D-G39C/K39C D-M9N/M9P/M9B D-M9NV/M9PV/M9BV D-F9G/F9H D-F8N/F8P/F8B D-Y59A/Y59B/Y7P* D-Y69A/Y69B/Y7PV* D-Y7G/Y7H D-M5N/M5P/M5B D-S991/S992/S99V1/S99V2 D-S9P1/S9P2/S9PV1/S9PV2 D-T991/T992/T99V1/T99V2 D-S791/S792 D-T791/T792 D-S7P1/S7P2 D-T791C/T792C 6-16-28 Grommet 6-16-29 Connector 6-16-30 Band 6-16-31 Terminal conduit 6-16-32 6-16-33 Grommet 6-16-34 Rail 6-16-35 Connector 6-16-36
Measurement mode] 18 Pressure Setting 19 3-Step Setting Mode 20 Simple Setting Mode 22 Function Selection Mode 24 Function selection mode 24 Default setting 24 F 0 Display units and switch output specifications function 26 F 1 Setting of OUT1 27 F 2 Setting of OUT2 30 F 3 Digital filter setting 32 F 4 Auto-preset function 33 F 6 Fine adjustment of display value 35 F10 Sub display setting 36
Definition and terminology 10 Mounting and Installation 13 Installation 13 Wiring 14 Pressure Setting 16 Outline of Settings 17 Initial Setting 18 3 Step Setting Mode 21 Simple Setting Mode 23 Function Selection Mode 25 Function selection mode 25 Default setting 25 F 0 Units selection function 27 F 1 Setting of OUT1 30 F 2 Setting of OUT2 33 F 3 Digital filter setting 35 F 4 Auto-preset function 36
If the convex side is mounted downward, it will interfere with the floor when the element is mounted on its bottom surface, causing breakage of the filter case and the element.) 36 - Doc. no. ZB-OM00201-B Replacement procedure for silencer* Turn the body upside down.
Summary of Product parts 12 Definition and terminology 13 Mounting and Installation 16 Installation 16 Piping 18 Wiring 20 Pressure Setting 23 Measurement mode 23 Function Setting 25 Function selection mode 25 Default setting 25 F0 Units selection function 27 F1 Setting of OUT1 28 F2 Setting of OUT2 31 F3 Response time 33 F4 Auto-preset function 34 F5 Analogue output / Auto-shift input 36