LFE-OMY0008 [F 2] OUT2 38 No.LFE*-OMY0008 c. / Add/dEC OUT1 (31 ) ( [n2AH]) ( [n2dH]) c.(32 ) 4. 4. 4. 4.
When accumulated output mode is selected" on (page 31) Press the button to set. Return to function selection mode. [F 2] Setting of OUT2 complete. Output mode d. When Accumulated pulse output mode is selected There is no item to set. -39No.LFE*-OMZ0011 [F 3] Response Time The response time of the switch output can be set.
Terminal Terminal resistance resistance 2 2 2 7 5 7 5 7 5 SDSD+ SDSG SD+ SD+ SD+ SG SDSG SDSG Master This product This product This product (first slave) (second slave) (31 slaves) st Do not connect any wire to other PIN numbers.
Terminal Terminal resistance resistance 2 2 2 7 5 7 5 7 5 SDSD+ SDSG SD+ SD+ SD+ SG SDSG SDSG Controller This product This product This product (Second) (31 device) st (First) Do not connect any wire to other PIN numbers.
The actuator not described for pulley ratio is calculated by 1/1. 31 - 5.3.6 Control mode selection To use position control mode (pulse input), navigate to the "Basic" tab of the "Parameter Setting" screen "Control mode selection" Please select "Position control mode". (PA01 parameter in the "Basic" tab of the List display also changes to "000".)
Adapter with throttle Rc1/4 ZS-31-X175 1 pc. -8No.PS-OMT0006-C Names of Parts of Product and Handling Precautions Names of parts of product Only fluids which are non-corrosive to C3604 + electroless nickel plated, AI203 (aluminum oxide) and FKM should be used. Handling precautions When piping, apply a spanner to the piping section of the sensor.
13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 51 Revision history G: Revise Safety Instructions.
No.1 OFF ON P2 No.2 OFF ON P3 No.3 OFF ON P4 No.4 OFF ON P5 P6 P7 P8 7 8 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 50 13 14 15 16 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 51 F : 2019 1 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +
Construction P.31 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Description Material Note 31 Auto switch 32 Magnet 33 Switch spacer Resin 24 - Angle adjustable type Component parts No.
Disassemble and reassemble 8-2-1 Caution on disassemble (1) Disassemble where clean and spacious place. (2) Cover the rotary actuator pipe inlet and the end of rubber hose after removing the rotary actuator. (3) Mind not to damage internal sliding surface of the rotary actuator when disassembling it. (4) Please consult with us when you have any question on disassembling and inspection. -31
/LEHS .20 4.1 . 20 4.2 . 21 4.3 . 22 5.23 5.1 . 23 5.2 . 24 5.3 . 27 . 27 . 29 (1). 31 (2). 32 (3). 33 . 34 5.4 . 36 . 36 . 38 1 - 6.39 7.40 7.1 . 40 7.2 . 41 7.3 . 41 7.4 . 42 7.5 . 44 7.6 . 44 8.45 8.1 . 45 8.2 . 46 8.3 . 50 8.4 . 53 .54 2 - LEH Series / (ISO/IEC)(JIS)1) 2) *1) ISO 4414: Pneumatic fluid power -General rules relating to systems ISO 4413: Hydraulic fluid power -General
Step 1 Step No. 0 Movement MOD Press the key. 31 - Set "Movement MOD(Movement mode). Show Movement MOD(Movement mode) in the second line on the screen, and select the choice with " " key and press the SET key to register. Movement MOD(Movement mode) When Absolute is selected : Target position is set on the absolute position with reference to the origin.
1 Stop-SW actived Reset Stop-SW OFF ON OFF ON PLC OFF OFF PLC ON CN1 EMGOFF CN1 EMGON 106 - 3 ON JOG 31 TB Ver.511 LEC-T1-S () Ver1.** Ver1.** Ver2.**2 Ver2.**1 LEC-T1-S ON/OFF ON LEC-T1ON OFF ON OFF OFF AX IS. Caution! 1 Enable SW is OFF Motor Blocked Turn ON it!
CN2: TB/PC connector.31 9. 1 How to use.31 10. LED display.32 10. 1 LED display.32 10. 2 Controller IF communication status and LED display.33 11. Mode.34 11. 1 Outline.34 11. 2. Step data input mode .34 11. 3. Numerical data input mode.34 11. 4. Data writing mode.36 12.
CN2: TB/PC connector.31 9. 1 How to use.31 10. LED display.32 10. 1 LED display.32 10. 2 Controller IF communication status and LED display.33 11. Mode.34 11. 1 Outline.34 11. 2. Step data input mode .34 11. 3. Numerical data input mode.34 11. 4. Data writing mode.36 12.
XS2C-D4** [OMRON Corporation] 31 - 8. 2 Wiring diagram For you reference, the example of wiring of the gateway unit CN1 is shown below. The communication line from the gateway unit CN1 branches to each controller (LEC) by the branch connector. It is recommended to connect the terminating resistor (120 1/4W) to the branch connector at the terminal.
LED display.31 9. 1 LED display.31 9. 2 Controller IF communication status and LED display.32 10. Mode.33 10. 1 Outline.33 10. 2 Step data input mode .33 10. 3 Numerical data input mode.33 10. 4 Data writing mode.35 11. Memory map .36 11.1 Memory assignment.36 11.2 Controller IF flagIN Data.40 11.3 Gateway unit status flagIN Data.40 11.4 Gateway unit control flagOUT Data.42 12.
) . 8 (2)GW . 8 (3)LEC . 8 (4)GW . 8 (5)GW . 8 (6) . 9 (7) . 9 3 . 10 3.1 . 10 3.2 . 12 3.3 . 13 (1)(LECGEN1) . 13 (2)DIN (LECGEN1D) . 13 3.4 . 14 (1) . 14 (2) . 14 4. . 15 4.1GW (B RATE) . 15 4.2 (CN2SW) . 16 4.3LEC . 16 4.4GW EtherNet/IP . 22 5. . 26 5.1 CN4 . 26 5.2 CN3 . 26 5.3 CN1CONT . 26 5.4 CN2PC/TB . 27 6.CN4 . 28 1 - 6.1 . 28 6.2 . 29 6.3 . 30 . 30 7.CN1(CONT) . 31
The Address assignment range is 1 to 31. The address can be set regardless of connecting order, but it is not possible to set address overlap. The address at shipment from the factory is 0.