This is a legacy product.
HRX-OM-Q026 HRX-OM-Q026-V Operation Manual Installation Operation Original Instructions Thermo Chiller HRSH Series HRSH100-A-20HRSH100-A-40HRSH100-A-20-S HRSH150-A-20HRSH150-A-40HRSH150-A-20-S HRSH200-A-20HRSH200-A-40HRSH200-A-20-S HRSH250-A-20HRSH250-A-40HRSH250-A-20-S HRSH300-A-20HRSH300-A-40HRSH100-W-20HRSH100-W-40HRSH100-W-20-S HRSH150-W-20HRSH150-W-40HRSH150-W-20-S HRSH200-W-20HRSH200-W-40HRSH200
For a facility with a large installation area that can vent the air naturally: Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility with a small installation area that can not vent the air naturally: Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
Applicable bore size (mm) A A1 E1 L1 MM U1 NX NZ L A Applicable bore size (mm) MM R R1 U1 NDH10 NX Applicable pin part no. A1 E1 L1 RR1 Part No.
When a load, such as a relay or solenoid valve, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
LEFS16A-100 NPN (2) Check Parallel I/O configuration matches (NPN or PNP). (2) 17 -
2.4 Construction
Leakage voltage Caution Take note that the leakage voltage will increase when a resistor is used in parallel with a switching element or when a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the leakage voltage passing through the C-R circuit. The suppressor residual leakage voltage should be as 3% or less of the rated voltage. 3.
A C A-A A B B A Auto switch mounting bracket A-A B-B Dust seal band type Seal band holder roller specification C No.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
9 r e !7 @1 !2 !6 !8 q !1 A B A' B' Without magnet Extension locking u t @5 @0 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com When shipped Section A-A' Retraction locking !0 !5 Section B-B' !3 !
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
set of a, b, c, d) BMA3-050 (A set of a, b, c, d) BMA3-063 (A set of a, b, c, d) CKQ D-M9ANote 2) BMA3-040S (A set of a, b, c, e) BMA3-050S (A set of a, b, c, e) BMA3-063S (A set of a, b, c, e) Auto switch Switch bracket (Resin) Transparent (Nylon)Note 1) d e White (PBT) c Switch holder b Auto switch mounting screw a * Band (a) is mounted so that the projected part is on the internal side
Air filter (5m or less) When using a solenoid valve, use a metal seal type (series VQ, VQZ, SQ, etc.).
Once in the mounting position, use a flat head watchmakers screwdriver to tighten the included set screw. Note) When tightening the set screw, use a watchmakers' screwdriver with a handle diameter of about 5 to 6 mm.
Applicable bore size (mm) A A1 E1 L1 MM U1 NX NZ L A Applicable bore size (mm) MM R R1 U1 NDH10 NX Applicable pin part no. A1 E1 L1 RR1 Part No.