o (Example) NVV3J1-S41-03-M5 NVJ114-5M2.. . 2 VJ100-19-1A .. . 1 a lt is impossibie to mount NVJ | 14O and NVJ124O together on the same manitold base. . In cas of NVJ124O manifold type, supply air to "R" port of manifold base, "P" port of maniiold base will be lhe exhaust Dort.
Do not rotate the cover. If a cover is rotated when installing a cylinder or screwing a fitting into the port, it is likely to damage the junction part with cover. 2.Do not operate with the cushion needle in a fully closed condition. Using it in the fully closed state will cause the cushion seal to be damaged.
(If you do not the power to OFF, it does not reflect the data in the driver.) Note2) Selected Items Write: It writes the parameter values of the corresponding frame to the driver. Single Axis Write: It writes all of the parameters to the driver. Note3) Do not change For manufacturer setting parameters.
(If you do not the power to OFF, it does not reflect the data in the driver.) Note2) Selected Items Write: It writes the parameter values of the corresponding frame to the driver. Single Axis Write: It writes all of the parameters to the driver. Note3) Do not change For manufacturer setting parameters.
Also, do not drop or apply a strong shock. Otherwise, damage or an accident can occur. Also, do not drop or apply a strong shock. Otherwise, damage or an accident may occur. 7. Do not affix any tape or seals to the body.
Do not use the auto drain valve in such environment.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not use in a location where radiated heat will be received from a heat source in the vicinity. 5.
Do not operate or set with wet hands. This may lead to an electric shock. End plate bracket (EX600-ZMA2) SUPPLIERS DECLARATION OF CONFORMITY Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Connector (Base only) (2) Add more units.
Do not use the cylinder in the locked state to sustain a load that involves impact.
Do not remove the name plate. 14. Perform periodic inspections and confirm normal operation, otherwise it may be impossible to guarantee safety due to unexpected malfunction or erroneous operation. 4. Do not touch connector terminals or internal circuit elements when current is being supplied.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water, steam, or where there is direct contact with any of these. 2. Products compliant with IP65 and IP67 enclosures (Based on IEC529) are protected against dust and water, however, these products cannot be used in water. 3.
Note 2) The output functions operate only for the real-time flow rate display, and do not operate for the accumulated flow display. Note 3) Window comparator mode Since hysteresis is 3 digits, separate P1 and P2 by 7 digits or more. 1 digit is the minimum setting unit (refer to the table above).
Weight g (oz) Model IN side, OUT side ZFC100-04 4 10 (0.35) 11.5 (0.41) ZFC100-06 6 20 (0.70) Metric size ZFC200-06 6 30 (1.05) 21.5 (0.76) ZFC200-08 8 50 (1.75) ZFC101-03 5/32" 10 (0.35) 11.5 (0.41) ZFC101-07 1/4" 20 (0.70) Inch size ZFC201-07 1/4" 30 (1.05) 21.5 (0.76) ZFC201-09 5/16" 50 (1.75) Note 1) Flow rate when initial pressure drop is 0.003MPa (0.44psi) or less.
In a locked state, do not apply impacts, strong vibrations or rotational forces. Do not apply a impacts, strong vibrations or rotational forces from external sources, because this could damage or shorten the life of the lock unit. 4. The locking of the fine lock cylinder is directional.
In a locked state, do not apply impacts, strong vibrations or rotational forces. Do not apply a impacts, strong vibrations or rotational forces from external sources, because this could damage or shorten the life of the lock unit. 4. The locking of the fine lock cylinder is directional.
Do not drop or bump the product. Dropping or bumping while handling may cause damage to the product. 5. Lead wire dimensions Pressure Supply Warning Covering: 3.4 Insulator: 1.1 Conductor: 0.64 1. Do not use the switch with corrosive gas or liquid. Do not use the switch with corrosive gas or liquid. Such gas or fluid may cause damage to the switch. Operating Environment Warning 2.
Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water, or where there is direct contact with same. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
Do not exceed specified current or the LED might be damaged and not function. 3. The indicator light is lit when switch is off for D-P70 4. Do not drop, dent, or allow excessive impact to cylinder during handling. 5. Keep at least 20mm away from each other when 2 or more cylinders with high magnetic field resistance auto switch are mounted in parallel. and D-P75.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.