CM2 Do not rotate the cover. If a cover is rotated when installing a cylinder or screwing a fitting into the port, it is likely to damage the junction part with cover. 2.Do not operate with the cushion needle in a fully closed condition. Using it in the fully closed state will cause the cushion seal to be damaged.
Compressed air is mainly used to do work by acting on a piston or vane -producing some useful motion tor instance. While many tacets of industry use compressed air, the general field of Industrial Pneumatics is considered here.
Do not put the heavy objects on the products. Do not use the products as scaffold. 2. Do not use the products in conditions that do not meet the product specifications. Product Returns When returning the product to SMC, make sure to properly purge to remove all hazardous materials and return the product complying with SMC specified procedures.
Failure to do so may cause the angle adjusting screw to become loose or drop.
Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (Otherwise, the operation of an auto drain will stop and drainage will discharge through the air outlet.) If it is unavoidable that the tube goes upward, make sure it only goes as far as the position of the auto drain outlet.
(If you do not the power to OFF, it does not reflect the data in the driver.) Note2) Selected Items Write: It writes the parameter values of the corresponding frame to the driver. Single Axis Write: It writes all of the parameters to the driver. Note3) Do not change For manufacturer setting parameters.
(If you do not the power to OFF, it does not reflect the data in the driver.) Note2) Selected Items Write: It writes the parameter values of the corresponding frame to the driver. Single Axis Write: It writes all of the parameters to the driver. Note3) Do not change For manufacturer setting parameters.
Do not use the auto drain valve in such environment.
Do not disassemble or modify the main unit. Operating Environment Warning Caution 1. Do not use in the following environments, as this can cause damage and reduced performance. 1. Do not step on or place heavy objects on the unit. 1. Locations with an atmosphere of corrosive gases, organic solvents or chemical solutions, and locations where there may be contact with the same. 2.
Do not operate multiple cylinders in synchronization. Avoid applications in which two or more end lock cylinders are synchronized to move one workpiece, as one of the cylinder locks may not be able to release when required. 2. Manual release (Lock type) While pushing the M/O knob, turn it 90 counterclockwise.
SQ2000 SQ1000 (1) (1) SQ2000 (2) (2) Bore 4 Bore 2 Bore 4.5 OFF position ON position
(If you do not cycle the power, it does not register the data in the driver.) Note2) Selected Items Write: Writes the parameter values of the corresponding frame to the driver. Single Axis Write: Writes all of the parameters to the driver. Note3) Do not change For manufacturer setting parameters.
IEC 60204-1: Safety of machinery -Electrical equipment of Do not use in an explosive atmosphere. Do not expose to direct sunlight. Use a suitable protective cover. Do not install in a location subject to vibration or impact. Check the Maintenance of pneumatic systems should be performed only by qualified personnel.
Do not use compressed air which contains chemicals, organic solvents or corrosive gases. Do not use compressed air containing chemicals, organic solvents, salt or corrosive gases, as this can cause damage and reduced performance, etc. 3. Operating pressure range The operating pressure range is determined by the equipment being used.
Do not drop or bump the product. Dropping or bumping while handling may cause damage to the product. 5. Lead wire dimensions Pressure Supply Warning Covering: 3.4 Insulator: 1.1 Conductor: 0.64 1. Do not use the switch with corrosive gas or liquid. Do not use the switch with corrosive gas or liquid. Such gas or fluid may cause damage to the switch. Operating Environment Warning 2.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system.
The received message is deleted if the calculation result and received CRC do not match.
An injury or failure can result. 3 Step Setting Mode Maintenance Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not indicate suffix N for no lead wire on D-A3/A44/G39/K39 models.
Do not service machinery/equipment or attempt to remove component until safety is confirmed. 1) Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 4-17-4