Series 10-SYJ300/500/700 Rubber Seal 3 Port Solenoid Valve (Coil temperature: 20C, at rated voltage, without surge voltage suppressor.) Note 2) Impact resistance: No malfunction occurred when it was tested in the axial direction and at right angles to the main valve and armature in both energized and de-energized states once for each condition.
The resistance of the solenoid valve is R 20 + 278 3% Ohm at 68F (20C). Do not bend or pull cables repeatedly. T4 Maximum surface temperature 275F (135C) Temperature class Hazardous Locations Specifications Terminal type (TT) L-type plug connector (L) LL-type plug connector (LL) Warning Electrical entry Note) 1.
Maximum Flow Capacity of the Compressor Intake Condition under Rated Conditions Model AFF70D AFF80D AFF90D Maximum flow capacity/Compressor intake condition*2 [m3/min] 7.3 11.5 15.1 *1 Flow at 20C, atmospheric pressure, and 65% of relative humidity *2 32C, flow rate when converted to atmospheric pressure *3 Filtration efficiency for the conditions below in addition to the rated conditions
Burst pressure Note) Min. bending radius (mm) 24 Burst pressure (MPa) Operating temperature Material 20C to 60C Nylon 12 Note) The value at temp. of 20C and with O.D. variable rate 10% max.
(mm) ASG32F-01 4 ASG42F-02 6, 8 ASG52F-03 6 ASG62F-04 Sealant: Special FKM Seat ring: Stainless steel 303 8 12 4, 6 8, 10 10, 12 460 920 790 1580 100 180 230 390 Flow rate (l/min (ANR)) Controlled (free) flow 7 14 12 24 1.5 2.7 3.5 6 Effective area (mm2) Applicable tubing materials Note) Flow rate is measured at 0.5 MPa and 20C.
Standard condition : Air in a temperature state of 20C, absolute pressure 0.1 MPa (= 100 kPa = 1 bar), relative humidity 65%. It is stipulated by adding the (ANR) after the unit depicting air volume.
Subsonic flow : Flow greater than the critical pressure ratio Standard condition : Air in a temperature state of 20C, absolute pressure 0.1 MPa (= 100 kPa = 1 bar), relative humidity 65%. It is stipulated by adding the (ANR) after the unit depicting air volume.
Residence time of water at 20C is 5.5 x 10-6 sec, whereas at 150C, it is 2.8 x 10-8 sec, or about 200 times shorter. The objective of baking is to exhaust water with long adsorption residence time more quickly. XVD Surface leakage This leakage occurs between surfaces of the sealing and the seal material.
Residence time of water at 20C is 5.5 x 10-6 sec, whereas at 150C, it is 2.8 x 10-8 sec, or about 200 times shorter. The objective of baking is to exhaust water with long adsorption residence time more quickly. XVD Surface leakage This leakage occurs between surfaces of the sealing and the seal material.
(Variation: 10%) *7 The value when there is an ambient temperature of 20C and when the rated voltage is applied. The value depends on the ambient environment.
In-line Air Filter RoHS Operating pressure range 100 kPa to 1.0 MPa (20C) Both positive pressure and vacuum pressure can be used with one unit! 5 m Filtration OUT IN 100 kPa 1.0 MPa Positive pressure e.g.)
Standard equipment AMF 1/2B 3/8B 1B (3) Accessory 11/2B SF Note 1) ANR indicates the flow rate converted to the value at 20C under the atmospheric pressure and the state of relative humidity 65%. Note 2) Based on discharge rate and discharge temperature (70C) of screw type compressors. Note 3) The accessories should be mounted by user.
At this time correction factor line becomes A . coefficient (1) To get correction factor of 1.35 use ambient temperature correction factor A at 20C. (2) (3) To get outlet air temperature divide 38.5C from (1) by 1.35 from (2).
Note 1) ANR indicates the flow rate converted to the value at 20C under the atmospheric pressure and the state of relative humidity 65%. Note 2) The accessories should be mounted by user.
(mm)Thickness (mm)BundleStraight pipeColorApplicable fluidMax. operating Note 1)pressure (at 20C)Burst pressure (at 20C)Note 2)radius (mm)Max. operating temperature (Fixed use)MaterialBasic diameterTolerance10 m20 m50 m100 m50 Ft. (16 m)100 Ft. (33 m)2 mInch sizes (Series TIL)TIL053/16andquot;3/16andquot; x 1/8andquot;4.75?0.10.8?0.08?
20 to 908.0 (at 20C)3.3 (at 20C)?0.10.45/0.65 (at 20 l/min)20Approx. 15Approx. 16Rc 3/4Stainless steel, EPDM, Copper brazing (Heat exchanger), PPS, Silicone, Fluororesin10 to 250.3 to 0.713/14Rc 1/2Stainless steel, EPDM, Copper brazing (Heat exchanger), Silicone, Brass3-phase 200 VAC 50 Hz, 3-phase 200 to 208 VAC 60 Hz Allowable voltage fluctuation ?
(Coil temperature: 20C, at rated voltage) 3-port (SX090) : Based on dynamic performance test, JIS B 8419.
Installation environment and power supply are within specification range and stable. 6 The capacity at the thermo-chiller outlet when the circulating fluid temp. is 20C. 7 Fluid flow to maintain the cooling capacity and the temperature stability.
cooling Refrigerant R134aHFC(WGP:1300) Refrigerant Charge Quantitiy 150 5g 200 5g 230 5g 270 5g 290 5g 3505g Air IN/OUT Connection Rc3/8 Rc1/2 Rc3/4 Rc1 Acceesory (Hexagon nipple) R3/8 R1/2 R3/4 R1 Drain Connection (Outside Diameter of Tubing) 10mm Color Panel: Urbanwhite1Base:Urbangray2 Weight 18kg 22kg 23kg 27kg 28kg 46kg Note1: The data for m3/ (ANR) is referring to the conditions of 20C
Note2) The above data is based on a room temperature of 20C. Note that you may obtain different figures, depending on temperature conditions. Note3) The above data shows compatibility guidelines based upon component parts. Therefore, it is no guarantee of product performance. In addition, using fluids other than those specified in the catalog are not covered by the products warranty.