SMC Corporation of America
Elite Part Number Search
Search Results "LEFG16-S-350"

Command Status Check sum code Reading cylinder stop output setting Command Block # 0 0 S R [CR] Unit No. Command Check sum code Response Block # 0 0 S R [CR] Unit No. Command Response Status Check sum code data Response data details 0 0 1 Stop output set time Unit: 0.1 (s) Writing cylinder stop output Command Block # 0 0 S W [CR] Unit No.

Reduced outgassing Resin materials eliminated Laser marking is employed for the model designation. o u d t g e 2 a c s u s d i Reduction of outgassing due to surface treatment e n o u d t g R e g a 1 c s u s d i e n R g All the external parts (made of aluminum alloy) such as the body and slide table are electroless nickel plated.

kit 16 stations 16 NKE Corp.: Uni-wire H System 1 to 8 stations SUNX Corp.: S-LINK System (16 output points) 8 SUNX Corp.: S-LINK System (8 output points) 1 to 4 stations 8 stations D side DeviceNet, CompoBus/D (OMRON Corp.) 16 16 stations 1 to 8 stations OMRON Corp.: CompoBus/S System (16 output points) OMRON Corp.: CompoBus/S System (8 output points) 8 8 stations 1 to 4 stations Mitsubishi

There is no "S" type for AC, since the generation of surge voltage is prevented by a rectifier. With light/surge voltage suppressor (non-polar type) There is no "S" type for AC, since the generation of surge voltage is prevented by a rectifier. D and DO type DC specifications are 24VDC or 12VDC only. D and DO type are for SY5000/7000 only.

Speed V (mm/s) V 500 mm/s Guideline for Selection of Bearing Type Bearing type Required conditions Impact load and vibration load are added. Change in load is large. Long life span is required. Slide bearing Selection of bearing type High accuracy (Little rattle is allowed.)

Example: Analog output = 1 to 5 [V] F .S. = 5 [V] 1 [V] = 4 [V] 3 [% F .S.] = 4 x 0.03 = 0.12 [V] The output error induced by the temperature change can be as much as 120 [mV].

Speed V (mm/s) V 500 mm/s MY CY Required conditions Guideline for Selection of Bearing Type Bearing type MG Selection of bearing type Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Impact load and vibration load are added. Change in load is large.

Speed V(mm/s) V 500mm/s CL MLGC CNA Guideline for selection of bearing style CB Bearing Required conditions Slection of bearing style CV/MVG Impact load and vibration load are added. Change in load is large. Long life span is required. Slide bearing CXW High accuracy (Little rattle is allowed.)

Reduced outgassing Resin materials eliminated Laser marking is employed for the model designation. o u d t g e 2 a c s u s d i Reduction of outgassing due to surface treatment e n o u d t g R e g a 1 c s u s d i e n R g All the external parts (made of aluminum alloy) such as the body and slide table are electroless nickel plated.

Regulator unit with 3 units Note 4) With ejector unit Note 5) Built-in silencer, Direct exhaust Special wiring specifications (except double wiring) Note 6) K L4 With name plate External pilot Note 7) N R S L3 L6 Built-in silencer, Direct exhaust L4 Note 1) In case of two or more options, enter them in alphabetical order.

Data L R S Piping Port Locaition Nil Operating direction Left Right L R S a b h g d c f e Note) Plugs are installed in ports other than those indicated for the model. Applicable Auto Switch/Refer to page 8-30-1 for further information on auto switches.

Data L R S Piping Port Locaition Nil Operating direction Left Right L R S a b h g d c f e Note) Plugs are installed in ports other than those indicated for the model. Applicable Auto Switch/Refer to page 8-30-1 for further information on auto switches.

Non-lube type Type Air Fluid 1.5MPa Proof pressure 1.0MPa Maximum operating pressure 0.15MPa Minimum operating pressure Without auto switch: 10C to 70C (with no freezing) Ambient and fluid temperature With auto switch: 10C to 60C (with no freezing) Pulling force Stroke (mm) Bore size (mm) Piston speed 50 to 700mm/s 50 to 1000mm/s Thread size N st + 1.4 0 to 1000 mm Stroke length tolerance

Reduced outgassing o u Resin materials eliminated Laser marking is employed for the model designation. d t g e a c 2 s u s d i e Reduction of outgassing due to surface treatment n o u d t R g g e a c 1 s u s d i e n R g All the external parts (made of aluminum alloy) such as the body and slide table are electroless nickel plated.

u s d Particulate generation has been reduced at the stroke ends by reducing impact using a sine cushion and by stopping the stroke using an internal stopper. i e Reduction of outgassing due to surface treatment n Impact acceleration [m/s2] o u d t R g g e a c 1 s u s d 5 i e n R g All the external parts (made of aluminum alloy) such as the body and slide table are electroless nickel plated

CEP: 09950-350, Brasil TEL: 11-4051-1177 FAX: 11-4071-6636 GREECE (Distributor) S.Parianopoulos S.A. 7, Konstantinoupoleos Street 11855 Athens, Greece TEL: 01-3426076 FAX: 01-3455578 DENMARK SMC Pneumatik A/S Knudsminde 4 B DK-8300 Odder, Denmark TEL: 70252900 FAX: 70252901 COLOMBIA (Distributor) Airmatic Ltda. Calle 18 69-05 Apart.