Stability of suction position, Flat type with groove (UM) Bellows type with groove (BM) 32 40 50 63 80 100 125 32 40 50 63 80 100 125 ZP3EA-P1 V V V V ZP3EA-P2 V V ZP3EA-P3 V V V ZP3EA-P4 V V ZP3EA-P5 V V ZP3EA-P6 V e Holder t Pad Form/Diameter Part no.
Refer to Table 4 Maintenance parts (P6) and Fig.1 Product construction (P7) of Chapter 2 Preparation for maintenance parts. Parts with the indication of Maintenance part can be replaced. 3. SMC specified parts should be used for service. Refer to the Construction / Maintenance parts table. Handling Caution 1.
The display will indicate PRG STEP P6 and the current number of brake operation The display number shows the operation number of No blinking. brake assembly that had been activated. 1 unit represents 10,000. Note: Setting is not required. Change the brake assembly, when the counter reaches 300.0.
Check through controller preset data (P6), which records brakes operation cycle no. Check the controller, when the value of 200.0 is reached, change brake unit.
Stations: 1 Station, Left Common Air Pressure Supply Port: 6 (ø6, Elbow), Right Common Air Pressure Supply Port: 6 (ø6, Elbow)
Stations: 1 Station, Left Common Air Pressure Supply Port: 0 (w/o Fitting, M5 x 0.8), Right Common Air Pressure Supply Port: 0 (w/o Fitting, M5 x 0.8)
Stations: 1 Station, Left Common Air Pressure Supply Port: ø6, Elbow, Right Common Air Pressure Supply Port: ø6, Elbow
Stations: 1 Station, Left Common Air Pressure Supply Port: w/o Fitting, M5 x 0.8, Right Common Air Pressure Supply Port: w/o Fitting, M5 x 0.8
Doc. no.SX90***-OMY0004 PRODUCT NAME Low Profile 2/3-Port Solenoid Valve MODEL / Series / Product Number SX90/090 Series Contents Safry Instructions P2,P3 Design Instrucrions P4 Selection P4 Mounting P5 Piping P5 Wrining P6 Air Supply P6 Operating Enviroment P6,P7 Maintenance P7 How to order P8 Specifications P8 Dimensions P9 Specific Product Precautions P9 Troubleshooting P10
No.VXP*-OMX0010 PRODUCT NAME PIROT OPERATED 2 PORT SOLENOID VALVE MODEL / Series / Product Number VXP Series Contents 1Safety Instructions P1,2 2Design P3 3Selection P3,4 4Mounting P4 5Piping P4 6Operating Environment P4 7Maintenance P5 8Precautions P5 9Return of Product P5 10Wiring P6 11Electrical Connections P6 12Pressure Terminology P6 13Applicable Fluids Check List P7 14Specifications
MQQ P6 Operating speed MQM P7 Operating speed 3) Lateral load Use within the allowable lateral load. MQQ P6 Allowable lateral load. MQM P7 Allowable lateral load. 4) Influence of abnormal Deformation and breakage of cylinder causes mechanism interference, eccentric load and overload. Get rid of these causes. external force . A: Creating a new chart by changing Specifications.
Parallel I/O type N P NPN PNP When controller equipped type (-P6) is selected when ordering the LE series, you do not need to order this controller. Confirm that the combination of the controller and the actuator is compatible. The controller is sold as single unit after the compatible actuator is set.
P6 Air leakage from the bonnet exhaust port. 2. Diaphragm is damaged. Replace the diaphragm assembly. P28 3. Foreign materials caught in seating part of the exhaust valve. Clean the seating part of the relief valve or replace the diaphragm assembly. P28 Air leakage 4. Foreign materials caught in the seating part or O-ring of the valve.
P6 Air leakage from the bonnet exhaust port. 2. Diaphragm is damaged. Replace the diaphragm assembly. P28 3. Foreign materials caught in seating part of the exhaust valve. Clean the seating part of the relief valve or replace the diaphragm assembly. P28 Air leakage 4. Foreign materials caught in the seating part or O-ring of the valve.
When measuring analog output of 1 to 5 VDC with a load impedance less than 100 k7, the analog output may not obtain the output accuracy of p6% or less (F.S.). Note 6) Adjustment of numerical values such as the zero/span adjustment is set based on the minimum units for output pressure display. Note that the unit cannot be changed. Note 7) This product is only for blowing gas.
Parallel I/O type N P NPN PNP When controller equipped type (-P6) is selected when ordering the LE series, you do not need to order this controller. Confirm that the combination of the controller and the actuator is compatible. The controller is sold as single unit after the compatible actuator is set.
restrictor With restrictor S Digital flow switch ON/OFF valve Nil Without digital flow switch NPN open collector 1 output + Analog output (1 to 5 V) PNP open collector 1 output + Analog output (1 to 5 V) NPN open collector 2 outputs PNP open collector 2 outputs NPN open collector 1 output + Analog output (4 to 20 mA) PNP open collector 1 output + Analog output (4 to 20 mA) P1 P2 P3 P4 P5 P6
Contents Contents P1 Safety Instructions P2 Handling precautions P4 Wiring method and LED indication P6 System configuration P7 Communication specification P7 Setting of dipswitch P8 Pressure setting and output monitoring P10 Communication data P10 Maintenance and inspection P11 1 - E/P Regulator Safety Instructions These safety instructions are intended to prevent hazardous situations and
Revision history A: P10 Addition note B: P6 Add cable color 0120-837-838 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2012 SMC Corporation All Rights Reserved 11 -
Precautions on model selection P6 6. Operation Principle P6 6-1. Extension locking (type F) 6-2. Retraction locking (type B) 7. Installation P9 7-1. Air supply 7-2. Piping 7-3. Operating environment 7-4. Mounting 7-5. Preparation before operation 8. Pneumatic circuit P12 9. Manual unlocking P14 10. Maintenance P16 10-1. Disassembly/ Replacement 10-2. Maintenance 10-3. Construction 11.