Your search for VFS2000 returned 29 result(s)
There were no hits with the full part number, but there were 3 hits in the keyword search.
There were no hits with the full part number, but there were 2 hits in the keyword search.
Product Information » New Products Search Results
Table of Contents AXT625-28-3A For 01T For 01T1 For 01C For 01F For 01SU Junction cover assembly AXT625-28-7AStations o VVF2000-26-5AStations AZ738-10AStations For 01T For 01SU AXT623-22 NBR Rubber plug !
Base type 01, 01T, 10: 2 to 15 stations 01C, 01F: 2 to 8 stations Blanking plate (Filter, Regulator) Blanking plate (Pressure switch) Stacking type Integrated type Nil 1 Number of manifold blocks required for mounting (stations) 2 2 2 2 2 2 2 1 Symbol Note) Stacking type: Base type 01, 01T Integrated type: Base type 01T, 01C, 01F Passage Porting specifications B, A EA, EB P Thread type
This is a legacy product, and replaced byVFS2100-3F-01T, VALVE, SOL/PILOT, 110 *LQA, VALVE, VFS2000 SOL VALVE 4/5 PORT, ND, VFS2000 BASE MT 1/8, 0.748 lb
Function: 3 (3 Position Closed Center), Body Option: 00 (Base Mounted Plug-in), Pilot: Internal Pilot, Voltage: 3 (110~120VAC 50/60HZ), Lead Wire: F (Plug-in)
Type: Solenoid Valves, Application: Unit for Manifold Mounting, Mounting Orientation: Manifold Base, Voltage: 110/120 V AC, Specification: Lubrication Free / Low Current, Valve Type: 5-Port Valve, Actuation: Double, Status at Power Off: Self-Recovery (Spring Return), Valve Positions: 3-Position Closed Center, Applicable Cylinder Diameter(Ø): -, Pipe Port Type: -, Port Size: -, Pressure Rating
2 Set at +1.50 deg.C 06 32 0D 37 Temperature setting (with writing EEPROM) F 01 3F 02 37 32 35 30 30 03 33 3F 0D 06 3F 0D Set at 25.0 deg.C 38 Offset setting (with writing EEPROM) F 01 3F 02 38 30 31 35 30 03 33 3F 0D 06 3F 0D Set at +1.50 deg.C HEC 6-1
06 32 0D Set at +1.50 deg.C 37 Temperature setting (with writing FRAM) F 01 3F 02 37 32 35 30 30 03 33 3F 0D 06 3F 0D Set at 25.0 deg.C 38 Offset setting (with writing FRAM) F 01 3F 02 38 30 31 35 30 03 33 3F 0D 06 3F 0D Set at +1.50 deg.C HECR 4-8 MODBUS communication function 5 MODBUS communication function MODBUS protocol is a communication protocol developed by Modicon.
Please refer to the content of Rx1B. 3B station READY (No used) 3C to 3F CC-Link system area 40 to 6F 70 to 7A CC-Link system area Only at Full numerical data instructions Remote The content of Remote station READY is as same as at Single numerical data instructions.
New Products Guide 2 Air Preparation Equipment, Modular F. R. L., Air Tanks Fittings and Tubing Flow Control Equipment, Exhaust Filters Switches/Sensors Process Valves High Vacuum Equipment Temperature Control Equipment Pneumatic Instrumentation Process Gas Equipment Equipment CAT.E00-7A INDEX New Products Guide 2 Air Preparation Equipment/ Modular F. R. L./Air Tanks Refrigerated Air Dryer
Please refer to the content of Rx1B. 3B station READY 3C to CC-Link system area 3F 40 to 6F 70 to CC-Link system area 7A Only at Full numerical data instructions Remote The content of Remote station READY is as same as at Single numerical data instructions.
(The solenoid valve does not have polarity.) 3) Remove the screw with washer (3f) from the bracket (3e). (For Y-shape type terminal, loosen the screw.) Mount crimped terminal (9) as shown below, and then re-tighten the screw (3f). Note) Tighten within the tightening torque of 0.5Nm+/-15%. Note: a) Wiring is possible with a bare lead wire.
Remove the self-up screw 3f from the bracket 3e (loosen it if using a Y shaped crimped terminal), mount the crimped terminal 3 as shown in the figure and fasten the self-up screw 3f again. The tightening torque should be within 0.5Nm+/-15%. 9 VEP-OMM0002-C VEP / VEF / VEA / VER Series Specific Product Precautions 4 Be sure to read before handling. VEA25 Wiring 2.
Skin the cable and crimp the crimped terminal (9) to the edges. 3) Remove the screw (3f) from the bracket (3e). (Loosen in the case of Y-shape type terminal.) As shown in the right figure, mount a crimped terminal (9), and then again tighten the screw (3f). Note) Tighten within the tightening torque of 0.5 Nm 15%. Note: a) It is possible to wire even in the state of bare wire.
Skin the cable and crimp the crimped terminal (9) to the edges. 3) Remove the screw (3f) from the bracket (3e). (Loosen in the case of Y-shape type terminal.) As shown in the right figure, mount a crimped terminal (9), and then again tighten the screw (3f). Note) Tighten within the tightening torque of 0.5 Nm 15%. Note: a) It is possible to wire even in the state of bare wire.
Skin the cable and crimp the crimped terminal (9) to the edges. 3) Remove the screw (3f) from the bracket (3e). (Loosen in the case of Y-shape type terminal.) As shown in the right figure, mount a crimped terminal (9), and then again tighten the screw (3f). Note) Tighten within the tightening torque of 0.5 Nm 15%. Note: a) It is possible to wire even in the state of bare wire.