S070 Replacement Parts Plug connector assembly (for plug lead) Sub-plate Lead wire length S07014A Port size S070S M3 M3 M5 M3 female thread M5 female thread 150 mm 300 mm 600 mm 1000 mm Nil 3 6 10 Gasket Mounting screw Valve model S070A S070B S070M Gasket no. S070A-80A-1 S070B-80A-1 S070M-80A-1 Valve model S070B S070C Mounting screw no.
MXF12 0.47 M2.5 x 8 MXF16 0.88 M3 x 10 MXF20 M4 x 14 2.06 Loctite No. 242 of Henkel Japan Ltd. or its equivalent is applied. 1-7.
The connection size is M3. Applicable crimped terminal width: 6.5mm or less [Wiring procedure] 1. Remove the front panel of the product. 2. Introduce the cable through the grommet with membrane to connect to the terminal block. (Refer to the label on the terminal block.) M3 tightening torque: 0.63 to 1Nm. Do not touch equipment other than the terminal block during wiring. 3.
The connection size is M3. Applicable crimped terminal width: 6.5mm or less [Wiring procedure] 1. Remove the front panel of the product. 2. Introduce the cable through the grommet with membrane to connect to the terminal block. (Refer to the label on the terminal block.) M3 tightening torque: 0.63 to 1Nm. Do not touch equipment other than the terminal block during wiring. 3.
ERR11 (2) Voltage sag happens. (3) Peltier device is short-circuited. (3) Restart the power supply with DC cable disconnected.
If the product is subjected to a short power outage (including voltage sag), it may take a long time to resume normal operation or be unable to restart normally due to the protective equipment triggered after the power is recovered.
If the product is subjected to a short power outage (including voltage sag), it may take a long time to resume normal operation or be unable to restart normally due to the protective equipment triggered after the power is recovered.
/h) (282 m3/h) (420 m3/h) (570 m3/h) dew point Standard Outlet air condition 45oF 155SCFM 215SCFM 314SCFM 406SCFM Air flow capacity pressure (7.2oC) (264 m3/h) (366 m3/h) (534 m3/h) (690 m3/h) (ANR) dew point (Note2) Outlet air 50oF 177SCFM 251SCFM 353SCFM 459SCFM pressure (10oC) (300 m3/h) (426 m3/h) (600 m3/h) (780 m3/h) dew point Rated Inlet air pressure 100 psi (0.7MPa) condition Inlet
Connector type (on this product side) M3 terminal block EIA RS-485 compliant Standards Protocol Special protocol: For details, refer to the Communications Specifications document.
Front L N PE To the users machine Terminal connecting screw: M3 Crimped terminal width: 6.5mm or less Applicable electric wire: 1.25mm2 or more Rubber grommet Power supply cable entry 131 13.
Example of the conventional measurement units (Reference) Unknown 6.0C 20C 26C 1.2 m3/h Fluorinated fluid Density : 1.80 x 103 kg/m3 : Unknown : 6.0C (6.0 K) : 20C (293.15 K) : 26C (299.15 K) : 20 l/min : Fluorinated fluid Density : 1.80 x 103 kg/m3 Heat generation amount Q Circulating fluid temperature difference T (= T2 T1) Circulating fluid outlet temperature T1 Circulating fluid return
M3 tightening torque: 0.63 to 1Nm. Do not touch equipment other than the terminal block during wiring. 3. Put back the front panel. [Remote control] Voltage is applied to the terminal block. Be sure to turn off the switch with lamp before wiring. 1) Disconnect the wires from no. 5 and 6 of the terminal block and mount the external switch.
M3 tightening torque: 0.63 to 1Nm. Do not touch equipment other than the terminal block during wiring. 3. Put back the front panel. [Remote operation] Voltage is applied to the terminal block. Be sure to turn off the switch with lamp before wiring. 1) Disconnect the wires from no. 5 and 6 of the terminal block and mount the external switch.
/min(ANR) 1.00 0.92 0.94 1.00 4.6 m3/min(ANR) 7.2 Refrigerant and GWP value Global Warming Potential (GWP) Revised Fluorocarbons Recovery Refrigerant Regulation (EU) No 517/2014 and Destruction Law (Based on the IPCC AR4) (Japanese law) R410A 2,088 2,090 Note 1: This product is hermetically sealed and contains fluorinated greenhouse gases (HFC).
If the product is subjected to a short power outage (including voltage sag), it may take a long time to resume normal operation or be unable to restart normally due to the protective equipment triggered after the power is recovered. In this case, turn off the switch of the product and reset the protection circuit referring to 6.2 Reset the Thermal relay and High Pressure Switch.
If the product is subjected to a short power outage (including voltage sag), it may take a long time to resume normal operation or be unable to restart normally due to the protective equipment triggered after the power is recovered. In this case, turn off the switch of the product and reset the protection circuit referring to 6.2 Reset the Thermal relay and High Pressure Switch.
If the product is subjected to a short power outage (including voltage sag), it may take a long time to start operating normally or be unable to restart normally due to the protective equipment triggered after the power is recovered. In that case, turn off the switch with lamp on the body once, and reset the protective equipment circuit referring to 5.2 Reset of protective equipment.
The following explains the compliance with "SEMI-F47 semiconductor process equipment voltage sag immunity test" of LECSS2-T series. (1) Parameter setting Setting [Pr. PA20] and [Pr. PF25] as follows will enable SEMI-F47. Parameter Setting value Description PA20 _ 1 _ _ SEMI-F47 selection PF25 200 Set the time [ms] of the [AL. 10.1 Voltage drop in the control circuit power] occurrence.
Type: Solenoid Valves, Application: Unit for Manifold Mounting, Mounting Orientation: Manifold Base, Voltage: DC5V, Specification: Standard, Valve Type: 3-Port Valve, Actuation: [Single] Single, Status at Power Off: Self-Recovery (Pressure Differential Return), Valve Positions: 2-Position Normally Open, Pipe Port Type: -, Port Size: -, Connecting Tube Diameter: -, Pressure Rating(MPa): 1,
Body Style: B (Base Mounted w/Screws), Coil Voltage: S (5 VDC), Flow Rate: A (Power Consumption: 0.35W, Operating Press: 0.1MPa, Cv: 0.016), Electrical Entry: G (Grommet)