SMC Corporation of America
Elite Part Number Search
Search Results "ISE2-01-15C"

10.2 8 10 17.6 10 5.5 2-3.3 Mounting hole 3.10-4 ZSE2/ISE2 Dimensions/Standard: ZSE201 T1 01 T1 01 T1 Grommet style/ZSE2-15 Connector style/ZSE2-15C Pressure setting Pressure setting Indicator light Indicator light trimmer trimmer 15 Lead wire length 600 15 (3000) H H L L 20 20 Lead wire length 600 Lead wire length 600 Lead wire length 600 (3000) 9.5 39 8.5 39 8.5 3.5 3.5 3.5 Mounting hole

13 11 Vacuum supply port 3.3 Gasket Vacuum supply port 3.3 Gasket 16-6-12 7 Compact Pressure Switch Series ZSE2/ISE2 01 T1 Dimensions: ISE2Grommet type: ISE2-15 01 T1 01 T1 Connector type: ISE2-15C Pressure setting trimmer Pressure setting trimmer L H SET L H SET 15 15 ZSE ISE Indicator light (Red) Indicator light (Red) 20 20 PSE Z I SE3 600 (3000) PS 600 (3000) Z I SE1 2 Courtesy of Steven

Y, Z directions 3limes each 12.6FS or lesis at 25'C 01: Rl/8. [.r5 x 0 8, Tl: NPT1/8, M5 x 0 8.

Y, Z directions 3limes each 12.6FS or lesis at 25'C 01: Rl/8. [.r5 x 0 8, Tl: NPT1/8, M5 x 0 8.

Model Section Type Round type Standard G27-10-R1 G36-10-01 G46-10-01 0.02 to 0.2 MPa setting G27-10-R1 G36-4-01 G46-4-01 Round type (with color zone) Standard G36-10-01-L G46-10-01-L 0.02 to 0.2 MPa setting G36-4-01-L G46-4-01-L Square embedded type Note 2) Standard GC3-10AS [GC3P-010AS (Pressure gauge cover only)] 0.02 to 0.2 MPa setting GC3-4AS [GC3P-010AS (Pressure gauge cover only

01-01 ZH07BS-01-01 ZH07BL-01-01 ZH10BS-01-01 ZH10BL-01-01 ZH13BS-01-02 ZH13BL-01-02 I J K L M N O P Model 1 8 Rc 1 8 Rc 1 8 Rc 1 8 Rc 1 8 Rc 1 8 Rc 1 4 Rc 1 4 ZH05BS-01-01 ZH05BL-01-01 ZH07BS-01-01 ZH07BL-01-01 ZH10BS-01-01 ZH10BL-01-01 ZH13BS-01-02 ZH13BL-01-02 57 12 3.2 31.5 Rc 5.8 2 38.5 57 12 3.2 31.5 5.8 2 38.5 57 12 3.2 31.5 5.8 2 38.5 57 12 3.2 31.5 5.8 2 38.5 60 12 3.2 33.5 5.8 2

Standard dew point temperature Standard dew point C 15 Symbol H Port size Symbol Bore Size Thread type 5 10 20 30 3 50 60 75 100 Nil N F Rc NPT G 01 1/8 02 1/4 04 1/2 03 3/8 Standard Specifications/Single Style (Standard Dew Point 15C [5F]) IDG3H IDG10H Standard dew point 15C (5F) Model IDG3H IDG5H IDG10H IDG20H IDG30H IDG50H IDG60H IDG75H IDG100H Compressed air Fluid Range of operating

Standard dew point temperature Symbol H Standard dew point (C) 15 Port size Symbol Bore Size Thread type 3 5 10 20 30 50 60 75 100 Rc NPT G Nil N F 01 1/8 02 1/4 04 1/2 03 3/8 Standard Specifications/Single Unit Type (Standard dew point: 15C) IDG3H Standard dew point 15C IDG10H Model IDG3H IDG5H IDG10H IDG20H IDG30H IDG50H IDG60H IDG75H IDG100H Compressed air Fluid Inlet air pressure

R1 1 ZX1 06 R ZZX1 Supply port location 01 1 Stations Arrangement (First station from the right end of the valve side is station 1.)

Note 1) 01 1 station Note 2) The number of max. stations differs from kit to kit. (Refer to the table below.)

If an adsorption confirmation switch is replaced for a vacuum switch on ZX100-K15LZ-PBC, indicate as ZSE2-0X-15C-D. In this case, mounting screws P3270148-39 (2 pcs.) are required. If the unit is used on its own, not combined with others, D is not required. Ex.)

Alarm Code.01 to 08, 10 to 19, 22, 24, 29, 30: Eliminate the error cause. Press the [RESET] key on the operation display panel or power cycle the main breaker to enable error recovery to take effect. Alarm Code.09: Eliminate the error cause.

Note 1) 1 station 01 16 stations Note) Number of terminals 16 Note 2) Refer to page 2-4216 for details.

C 1. ##0016 ## 00 01 1 02 2 03 3 04 4 05 5 06 6 07 7 08 8 09 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 2. **No. 3.

SERIES 15 FLOW CHARTS 400 400 1/32 1/32 3/64 3/64 1/16 1/16 3/32 3/32 1/8 1/8 ORIFICE-INCH ORIFICE-INCH 100 100 50 50 PRESSURE PRESSURE DROP ROP PSI PSI 10 10 5 01 01 02 02 05 05 1 2 5 WATER FLOW-GPM SERIES 50 FLOW CHARTS COAST PNEUMATICS 8055 E.

PSI PSI 10 10 5 01 01 02 02 05 05 1 2 5 WATER FLOW-GPM SERIES 58 FLOW CHARTS 97 SOLENOID VALVES . . .

Temperature range which can be set with the Thermo-chiller 10C to 35C Example) Facility water temperature of customers machine: 15C Temperature difference between the circulating fluid and facility water is: 50 15 = 95F (35C). 4.What is the kW for the required cooling capacity?