Table of Contents Secure the switch at an appropriate position with a flat head watchmakers screwdriver as indicated in Figure 3. Tightening torque: 0.05 to 0.1 Nm Second groove MRHQ 10, 16 3. Install the switch case, with a switch attached securely in the hole, in the direction indicated in Figure 1.
Then reinstall the stopper lever and parallel pin in their original positions and secure in place by tightening with the three bolts . MHS MHC MHT 6. Reinstall the rotary unit in its original position and secure in place by tightening with the four bolts .
IN L/A OUT OUT ST(M)-LED OFF I/O () ON/OFF SII/O / SI -21No.EX-OMS0026CN PWR-LED () PWR(V)-LED OFF () OFF () -22No.EX-OMS0026CN MS-LED SI NS-LED IP TM EtherNet/IP TM EtherNet/IP TM EtherNet/IP IP -23No.EX-OMS0026CN Bus IN No Link, No Activity Bus IN Link, No Activity(100 Mbps) Bus IN Link, Activity(100 Mbps) Bus IN Link, No Activity(10 Mbps) Bus IN Link, Activity
EX245-SPN1 GSD . 41 EX245-SPN1 Diagnostics type 1 4 (IN) 1 5.1.1. Diagnostics type 1 Diagnostics type 2 4 (IN) 1 5.2.2. Diagnostics type 2 Valves (16 coils) 2 (OUT) 12 6.3. Valves (32 coils) 4 (OUT) 12 EX245-DX1-X36 2 (IN) 210 7.4. EX245-DY1-X37 1 (OUT) 210 8.4.
Reducing the piping between the cylinder and valve offers approximately 50% reduction in air consumption. Choose from side and axial piping.
Base mount EX500 type plug-in manifold for VQC1000 valve, Protective enclosure conforms to IP67 for protection from dust and moisture, Gateway type serial transmission system, Maximum 16 stations available as standard, Optional DIN rail mount, 21 port sizes available 4/5 PORT SOLENOID VALVE. VQC Manifold. 1057 lb. VVM.
Base mount EX500 type plug-in manifold for VQC1000 valve, Protective enclosure conforms to IP67 for protection from dust and moisture, Gateway type serial transmission system, Maximum 16 stations available as standard, Optional DIN rail mount, 21 port sizes available 4/5 PORT SOLENOID VALVE. VQC Manifold. 1057 lb.
In ordering, specify the part nos. in the order from the 1st. station on D side.
In the case of voltage specifications other than 12 or 24 VDC, take care to avoid mistaking polarity, as there is no diode to prevent reverse current. In the event that lead wires are connected in advance, they will be as shown below.
(Value in the initial state) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz in the axial direction and at a right angle to the main valve and armature in both an energized and a de-energized state, once in each condition.
(Default settings) No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed in both energized and de-energized states in the axial direction and at right angles to the main valve and armature.
When using the lock unit by placing it in parallel with the cylinder for driving as shown in the figure below, align the cylinder with the rod. Doing so may result in a decrease in holding force. Take additional safety measures when conducting equipment maintenance.
Built-in silencer, Direct exhaust [-S] VFS This is an exhaust port on the manifold end plate. The built-in silencer exhibits an excellent noise suppression effect. (silencing effect: 30dB) Note) A large quantity of drainage generated in the air source results in exhaust of air together with drainage. See p.1.10-196 for maintenance.
line, and the cylinder stroke can be controlled in two stages in both directions.
IP65 MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN (mm) 8 7 6 5 4 3 2 1 Stations 185.5 173 160.5 148 135.5 123 110.5 98 Rail length L1 175 162.5 150 137.5 125 112.5 100 87.5 Mounting pitch L2 158 146 134 122 110 98 86 74 Manifold length L3 13.5 13.5 13 13 12.5 12.5 12 12 L4 Input block (M12) only (Pitch) P = 20
IP65 MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN (mm) 8 7 6 5 4 3 2 1 Stations 185.5 173 160.5 148 135.5 123 110.5 98 Rail length L1 175 162.5 150 137.5 125 112.5 100 87.5 Mounting pitch L2 158 146 134 122 110 98 86 74 Manifold length L3 13.5 13.5 13 13 12.5 12.5 12 12 L4 Input block (M12) only (Pitch) P = 20
(In the case of standard cylinders, port must be positioned in the upper side.) Define the upper side to be A, and then B, C, and D in a clockwise order. 2.