Support Guide/11-LEFG Series This value is the maximum torque (the limit value) in the Position control mode, Speed control mode or Positioning mode. When the product is Unevenness of a workpiece or base mounted on the body of the product may cause play in the guide and an increase in the sliding resistance. 10. When mounting the product, keep a 40 mm or longer diameter for bends in the cable. 11.
In the case of actually setting the auto switches, adjust them after confirming their operation. Note 2) Negative figures in the table show dimensions mounted inside cylinder body. Note 3) In the case of 5 mm stroke or the 10 mm stroke, there are times in which the switch will not turn OFF or 2 switches will turn ON simultaneously due to their movement range.
Epoxy resin containing glass fiber and polycarbonate is used in some parts of the D.P. Lube and the D.P. Lube Unit.
In ordering, specify the part nos. in the order from the 1st. station on D side.
The SY is available in body ported or base mounted styles, and can be used individually or manifold mounted.Plug-in connector connecting base , Side or bottom ported , Available with external pilot , Circular connector kit , One-touch fittings 4/5 PORT SOLENOID VALVE. SS5Y5 7 STA MANIFOLD BASE. 1054 lb. VVM.
In the case of voltage specifications other than 12 or 24 VDC, take care to avoid mistaking polarity, as there is no diode to prevent reverse current. In the event that lead wires are connected in advance, they will be as shown below.
(Value in the initial state) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz in the axial direction and at a right angle to the main valve and armature in both an energized and a de-energized state, once in each condition.
(Default settings) No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed in both energized and de-energized states in the axial direction and at right angles to the main valve and armature.
When using the lock unit by placing it in parallel with the cylinder for driving as shown in the figure below, align the cylinder with the rod. Doing so may result in a decrease in holding force. Take additional safety measures when conducting equipment maintenance.
Built-in silencer, Direct exhaust [-S] VFS This is an exhaust port on the manifold end plate. The built-in silencer exhibits an excellent noise suppression effect. (silencing effect: 30dB) Note) A large quantity of drainage generated in the air source results in exhaust of air together with drainage. See p.1.10-196 for maintenance.
line, and the cylinder stroke can be controlled in two stages in both directions.
IP65 MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN (mm) 8 7 6 5 4 3 2 1 Stations 185.5 173 160.5 148 135.5 123 110.5 98 Rail length L1 175 162.5 150 137.5 125 112.5 100 87.5 Mounting pitch L2 158 146 134 122 110 98 86 74 Manifold length L3 13.5 13.5 13 13 12.5 12.5 12 12 L4 Input block (M12) only (Pitch) P = 20
Series ZCUK is available in 5 bore diameters., Cyl, Free Mount for Vacuum, COMPACT CYLINDER W/VACUUM, M06, 1054 lb
The bearing is a recirculating linear guide in a stainless steel housing. Air slide table w/built-in guide rail, Bore size *: 6, 8, 12, 16, 20, 25, Standard or symetric styles, Adjuster options: rubber stopper, shock absorber, metal stopper, Auto switch capable, Cyl, Slide Table, Secondary Batt Comp, GUIDED CYLINDER, D79, 1054 lb
IP65 MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN (mm) 8 7 6 5 4 3 2 1 Stations 185.5 173 160.5 148 135.5 123 110.5 98 Rail length L1 175 162.5 150 137.5 125 112.5 100 87.5 Mounting pitch L2 158 146 134 122 110 98 86 74 Manifold length L3 13.5 13.5 13 13 12.5 12.5 12 12 L4 Input block (M12) only (Pitch) P = 20
(In the case of standard cylinders, port must be positioned in the upper side.) Define the upper side to be A, and then B, C, and D in a clockwise order. 2.
These products are intended for use in general factory automation equipment. Avoid using these products in machinery/equipment which affects human safety, and in cases where malfunction or failure can result in extensive damage. 2. Do not use in explosive environments, in the presence of inflammable gases, or in corrosive environments. This can cause injury or fire. 3.
Note 2) Impact resistance No malfunction occurred when it was tested in the axial direction and at right angles to the main valve and armature in both energized and de-energized states once for each condition. (Default settings) Vibration resistance No malfunction occurred in a one-sweep test between 45 and 2000 Hz.