Air Cylinder Series CS1 MB1 Rod End Nut Y Type Double Knuckle Joint CA2 ND hole H10 Shaft d9 CS1 Material: Cast iron CS2 Applicable bore size (mm) E1 L1 MM NX NZ U1 A1 RR1 NDH10 Part no.
Rod Boot Material I Bore size (mm) 125 140 160 Material Max. amhien1 temwaiure Symbo .. '" en 0 Foot" CS2-L12 CS2L14 CS2 l1 6 J l 58 ~ F Nylon tarpaulin Flange CS2 F12 CS2-F14 CS2-F16 Heal resisHlnt tarpaulin K 230 ~ F ' Single clevis CS2-C12 CS2C14 CS2-C16 ' MaKimum ambu~nt lemperalUre lor the rod 0001 {tsell.
Option Double knuckle joint (Clevis pin, Cotter pin) CS2 Symbol Specifications Rod boot XA Change of rod end shape In the case of using the rod end nut together with the single knuckle joint or double knuckle joint, refer to page 429.
No display 123,450 L (only lower digits are displayed). 123,456,780 L 9,999,999,999 L (maximum accumulated flow value exceeded) -58No.PF-OMZ0002-A
[F14] Zero-cut setting A function to force the display to zero to remove flickering at the lower measurement range.
No display 123,450 L (only lower digits are displayed). 123,456,780 L 9,999,999,999 L (maximum accumulated flow value exceeded) -54No.PF-OMY0002
[F14] Zero-cut setting A function to force the display to zero to remove flickering at the lower measurement range.
The range to display zero can be changed. < Operation > Display [F14] by pressing or button in function selection mode. Press the S button. Select Zero cut-off setting.
The range to display zero can be changed. < Operation > Display [F14] by pressing or button in function selection mode. Press the S button. Select Zero cut-off setting.
The zero cut-off range is 0.0 to 10.0%F.S., and can be set in 1.0%F.S. increments. < Operation > Display [F14] by pressing UP or DOWN button in function selection mode. Press the SET button. Move on to select zero cut-off setting (flow rate).
The range to display zero can be changed. < Operation > Display [F14] by pressing or button in function selection mode. Press the S button. Select Zero cut-off setting.
(Hysteresis mode, error output, switch output off) (Window comparator mode) -48No.PF-OMU0007-D
[F14] Display with zero cut-off setting When the flow is close to 0 L/min., the product rounds the value down and zero will be displayed. This is adjustable within the range of 10% F.S. of the flow range.
[F13] Setting for reverse display mode completed -49No.PF-OMW0007-E
[F14] Zero cut-off setting This function forces a zero display when the flow is within the 0 to 10% area of the flow range.
[F14] Zero cut-off setting completed : When setting the flow value and hysteresis within zero cut-off settable range, the on-off point varies depending on the settable range. However, please note that the setting and hysteresis of the switch output will not be changed.
] Zero-cut 0 1.0F.S.0.010.0F.S. <> UP DOWN [F14] SET Zero-cut Zero-cut UP DOWN Zero-cut Zero-cut 1%F.S.cut 2%F.S.cut 10%F.S.cut ISE70(1 MPa )[MPa] 1 MPa P_1=0.015[MPa]H_1=0.01[MPa]Zero-cut1.0 [MPa] 0.0(Zero-cut) 1.0(1%F.S.cut) Zero-cut (1.0%) Zero-cut SW SET [F14] Zero-cut -45No.PS-OMV0003CN-G [F80] 30 <> UPDOWN[F80] SET UP DOWN SET [F80] 30 () [ECo] (ON) ON OFF -46No.PS-OMV0003CN-G
] Zero-cut 0 0.010.0F.S.1.0F.S. <> UP DOWN [F14] SET Zero-cut Zero-cut UP DOWN Zero-cut Zero-cut 1%F.S.cut 2%F.S.cut 10%F.S.cut ISE70G(1 MPa )[MPa] 1 MPa P_1=0.015[MPa]H_1=0.01[MPa]Zero-cut1.0 [MPa] 0.0(Zero-cut) 1.0(1%F.S.cut) Zero-cut (1.0%) Zero-cut SW SET [F14] Zero-cut -48No.PS-OMV0008CN-E [F80] 30 <> UPDOWN[F80] SET UP DOWN SET [F80] 30 () [ECo] (ON) ON OFF -49No.PS-OMV0008CN-E