Your search for CM2 returned 30 result(s)
There were no hits with the full part number, but there were 22 hits in the keyword search.
There were no hits with the full part number, but there were 17 hits in the keyword search.
Product Information » New Products Search Results
Table of Contents Type V regulator (AR) is modified to produce the micro mist separator regulator (AWD).
ID05 AC200/200220 (50/60Hz) ID06 AC220 (50Hz) Permissible voltage change % voltage ratings -15+10 Apparent power V A 26/21 31/27 Rc Tube connection caliber 1/4 1/2 3/4 G NPT Mass kg 7 8.5 18.5 25 1 Condition entrance air pressure:0.7MPa temperature of entrance air At 35 oC saturation 2 Condition entrance air pressure:0.7MPa temperature of entrance air at the time of 20 oC (The saturation
Magnet: D (Built-in), Type: Pneumatic, Mounting: L (Axial Foot), Bore: 20mm, Port Thread: TN (NPT), Stroke: 300mm, Cushion: Rubber Bumper, Rod End Thread: Male Rod End, Rod Boot: None, Pivot Bracket: None, Rod End Bracket: V (Single Knuckle Joint)
Magnet: Built-in, Type: Pneumatic, Mounting: Axial Foot, Bore: 20mm, Port Thread: NPT, Stroke: 300mm, Cushion: Rubber Bumper, Rod End Thread: Male Rod End, Rod Boot: None, Pivot Bracket: None, Rod End Bracket: Single Knuckle Joint, Auto Switch: -, Leadwire or Prewired Connector: -, Number: -
Magnet: D (Built-in), Type: Pneumatic, Mounting: L (Axial Foot), Bore: 20mm, Port Thread: TN (NPT), Stroke: 300mm, Cushion: Rubber Bumper, Rod End Thread: Male Rod End, Rod Boot: None, Pivot Bracket: None, Rod End Bracket: V (Single Knuckle Joint), Auto Switch: A93--Reed, DC Volt, AC Volt, LED, Horizontal, Leadwire or Prewired Connector: L (3m)
Magnet: Built-in, Type: Pneumatic, Mounting: Axial Foot, Bore: 20mm, Port Thread: NPT, Stroke: 300mm, Cushion: Rubber Bumper, Rod End Thread: Male Rod End, Rod Boot: None, Pivot Bracket: None, Rod End Bracket: Single Knuckle Joint, Auto Switch: A93--Reed, DC Volt, AC Volt, LED, Horizontal, Leadwire or Prewired Connector: 3m, Number: -
Magnet: D (Built-in), Type: Pneumatic, Mounting: L (Axial Foot), Bore: 20mm, Port Thread: TN (NPT), Stroke: 300mm, Cushion: Rubber Bumper, Rod End Thread: Male Rod End, Rod Boot: None
Magnet: Built-in, Type: Pneumatic, Mounting: Axial Foot, Bore: 20mm, Port Thread: NPT, Stroke: 300mm, Cushion: Rubber Bumper, Rod End Thread: Male Rod End, Rod Boot: None, Pivot Bracket: -, Rod End Bracket: -, Auto Switch: -, Leadwire or Prewired Connector: -, Number: -
This is a legacy product, and replaced byCA2T63-300Z CA1/CA2 TIE-ROD CYLINDER. CYL, TIE ROD, NON-LUBE. ACTUATOR. 63MM CA1 DOUBLE-ACTING. 10.60147 lb. PD.
This is a legacy product, and replaced byCY1SG15-300Z, CYL, RODLESS, SLIDER, ACTUATOR, CY1S GUIDED CYLINDER, GM, 15MM CY1S SLIDE BEARING, 2.51040 lb, Bore size (mm)ModelAllowable load mass (Wv)(kg)Maximum operating pressure (Pv) (MPa)15CY1S15H7.00.65
This is a legacy product, and replaced byCDM2C32-300Z, CYL, RND BODY, DBL ACTING, ACTUATOR, CM2/CM3 ROUND BODY CYLINDER, LE, 32MM CM2 DBL-ACT AUTO-SW, 2.10596 lb
This is a legacy product, and replaced byCDG1RA63-300Z-C73L, CYL, AIR, BLOCK MT. AUTO-SW, ACTUATOR, CG/CG3 ROUND BODY CYLINDER, PE, 63MM CG DBL-ACT AUTO-SW, 7.57444 lb
(Inlet air pressure: 0.7 MPa, Inlet air temperature: 20C) Accessory (Option)/Replacement Parts Applicable model ID20 ID30 ID40 ID60 6604113 6604113 660651 660651 ID-200S ID-300S ID-400S ID-600S ID-200Z ID-300Z ID-400Z ID-600Z ID-DPM8 Bracket Adsorbent set Note) Adsorbent set (for low dew point) Note) Indicator set Note) Adsorbent and adsorption tube filter for one air dryer (two adsorption
This is a legacy product, and replaced byMBD63TN-300Z, CYL, TIE ROD, ACTUATOR, MB TIE-ROD CYLINDER, PD, 63MM MB DOUBLE-ACTING, 12.34588 lb
This is a legacy product, and replaced byMBL50-300Z, CYL, TIE ROD, ACTUATOR, MB TIE-ROD CYLINDER, ND, 50MM MB DOUBLE-ACTING, 6.52779 lb
This is a legacy product, and replaced byMGPM20-300Z, CYL, GUIDE, SLIDE BEARING, ACTUATOR, 40MM MGQ EUROPEAN, 5.61000 lb, Bore size (mm)ModelStandard stroke (mm) 1020253040507510012515017520040MGQM40??1.65??2.242.462.873.283.694.104.51