-XC12 to XC17, XC20/XC21 3 Change of Angle Adjustable Range (0 to 100, 90 to 190) CRB2 Symbol: C12 Symbol: C13 CRQ2B CDRQ2B X C12 Refer to How to Order on page 256. The rotation angle can be adjusted between 0 and 100. The rotation angle can be adjusted between 0 and 100.
MSU Symbol -XC12 to XC17, XC20/XC21 CRJ L L Specifications B B Applicable shaft type S, W, Y, X, Z, T, J, K CRA1 End of rotation Rotation starting point Additional Reminders CRQ2 A The rotation starting point is the position of the flat and the key groove when the actuator is pressurized through connection port B. Only XC12 and XC16 are compatible with shaft types X, Z, T, J and K.
to -XC21: Change of Angle Adjusting Range (0 to 100, 90 to 190) Please consult with SMC for further information on specifications, dimensions and delivery. 23 -XC12 to XC21 Change of Angle Adjustable Range (0 to 100, 90 to 190) 3 Symbol: C12 Symbol :: C13 CRQ2B CDRQ2B X C12 Refer to How to Order on page 11-8-12 .
NCA D-X 20Data 6-17-71 55 Made to Order Common Specifications: -XC12: Tandem Cylinder Symbol -XC12 20 Tandem Cylinder Dimensions (Dimensions other than below are the same as standard type.)
A full range of order made specifications -XA0 to XA30 -XB5 -XB6 -XB13 -XC3 -XC4 -XC5 -XC6 -XC7 -XC8 -XC9 -XC10 -XC11 -XC12 -XC18 -XC22 -XC30 -XC35 -X846 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Modification of rod end shape Heavy duty rod Heat resistant cylinder (to 150C) Low speed cylinder Special port locations With heavy duty scraper Heat resistant cylinder (to 110C) Stainless
port position XC4 With heavy duty scraper XC5 Heat-resistant cylinder (10 to 110C) XC6 Made of stainless steel Tie-rod, cushion valve, tie-rod nut, etc. made of stainless steel XC7 XC8 Adjustable stroke cylinder/Adjustable extension type XC9 Adjustable stroke cylinder/Adjustable retraction type XC10 Dual stroke cylinder/Double rod type XC11 Dual stroke cylinder/Single rod type 32 to 125 XC12
Dual stroke/Double rod -XC10 10 Tandem type -XC12 12 Two cylinders are combined in a back-to-back configuration, allowing the two reciprocating cylinder strokes to be controlled in three steps. Two cylinders are connected in-line, allowing cylinder output to be doubled. Standard part no.
MB XC12 Tandem cylinder Specifications Action Min. operating pressure Cushion Mounting Double acting, Single rod 0.1MPa Air cushion B, L, F, G, C, D type (T not available) The specifications other than the above are the same as those of the standard type.
(Example) CDA2L40-100Z 3 n 3 pcs. n pcs. Cylinder stroke (mm) For details, refer to the next page. Applicable Auto Switches/Refer to page 1263 to 1371 in Best Pneumatics No. 2 for further information on auto switches.
(Or None in the Case of No Switch), Stroke Options: XC12 (Tandem Cylinder)
(Or None in the Case of No Switch), Stroke Options: XC12 (Tandem Cylinder)
Magnet: Built-in Magnet, Mounting: Basic, Double-side Bossed, Bore Size: 40mm, Port Thread: Rc, Stroke A: 75mm, Rod End Thread A: Male Rod End, Rod Boot A: None, +: None, Stroke B: None, Cushion: Rubber Bumper, Rod End Thread B: Male Rod End, Rod Boot B: None, Pivot Bracket: None, Rod End Bracket: None, Auto Switch: No Switch, Lead Wire or Prewired Connector: 0.5m (Or None in the Case of
XC69 Fluororubber seal Shaft and parallel key made of stainless steel X6 Among the symbols XC8 to XC21, only XC12 and XC16 are compatible with shaft types X, Z, T, J and K. DCaution (1) The angle adjusting screw (angle adjustment bolt) is set at random within the adjustable rotating range. Therefore, it must be readjusted to obtain the angle that suits your application. 247
X6 T,J,K Among the symbols XC8 to XC21, only XC12 and XC16 are compatible with shaft types X, Z, T, J and K. DMoisture Control Tube IDK Series When operating an actuator with a small diameter and a short stroke at a high frequency, the dew condensation (water droplet) may occur inside the piping depending on the conditions.
Clean Series 40 to 63 Copper and Fluorine-free Water resistant (NBR seal) 40 to 100 Water resistant (FKM seal) Change of rod end shape Oversized rod cylinder Heat-resistant cylinder (10 to 150 C) Special port position With heavy duty scraper Heat-resistant cylinder (10 to 110 C) Made of stainless steel Tie-rod, cushion valve, XC7 tie-rod nut, etc. made of stainless steel XC8 XC9 XC10 XC11 XC12
-XC11 Dual stroke cylinder/Single rod type -XC12 Tandem type cylinder -XC13 Auto switch rail mounting style -XC18 NPT finish piping port Rod Boot Material -XC20 Head cover axial port Maximum operating temperature -XC22 Fluoro rubber seals Symbol Rod boot material -XC29 Double knuckle joint with spring pin Nylon tarpaulin J 70C -XC35 With coil scraper 110C Heat resistant tarpaulin K -XC37
and rod end nut made of stainless steel 25 301 to 400 10 mm 15 mm -XC8 Adjustable stroke cylinder/Adjustable extension type 32 301 to 450 20-XC9 Adjustable stroke cylinder/Adjustable retraction type 25, 50, 75, 100, 125, 150, 200, 250, 300 40 15 mm 20 mm 1500 301 to 800 D-B59W -XC10 Dual stroke cylinder/Double rod type Data 50, 63 301 to 1200 -XC11 Dual stroke cylinder/Single rod type -XC12
Select the desired range (“-XC12” to “-XC15”) and add the corresponding suffix to the end of the CDRQ2BSP40-90 part number. Check the catalog for details on the “-XC12” to “-XC15” suffixes as the position of the start and end points vary.
The CRQ2 series catalog can be found here.
dual stroke with 3 position (single rod type) ; XC12 is tandem dual force cylinder ; Bore sizes (mm): 20, 25, 32, 40 ; Variety of switches and lead wire lengths
dual stroke with 3 position (single rod type) ; XC12 is tandem dual force cylinder ; Bore sizes (mm): 20, 25, 32, 40 ; Variety of switches and lead wire lengths