Pin Cylinder/Single Acting, Spring Return

When embedded O-ring Air Machining dimensions for mounting Sealed with O-ring Air Bore size (mm) Stroke A B C D E F G 5 12 8.5 6 4 3.5 M8X1.0 6.5 3 10 20 16.5 14 15 28 24.5 22 5 16 12.5 10 6 3.5 M10X1.0 8.5 3 10 23 19.5 17 15 30 26.5 24 5 17 13.5 10.5 10 3.5 M15X1.5 12 4 10 23.5 20 17 15 30.5 27 24 5 19 14.5 11.5 16 4.5 M22X1.5 19 5 10 25 20.5 17.5 15 31.5 27 24 Note) E and F should be machined

AC Servo Motor Driver (Pulse input type/Positioning type)

300ms) c) Deceleration time constant (300ms) b) Acceleration time constant (200ms) a) Servo motor speed (1000r/min) a) Servo motor speed (1000r/min) Forward rotation 0r/min Servo motor speed d) Absolute move command (1000 10STM m) f) Absolute move command (2000 10STM m) e) Dwell command time (100ms) 91 - 8.

RS2H-OM0045P

. :0.1 D 50 : : mmax 1 RS2H mmax : mmax (Kg) =0.1 =0.2 NO 50 400 280 mAm max 63 530 365 YES 80 800 565 V m mmax=0.1 200<400 mP6 -1-* -1-1V=20m/minm=278(Kg) 200278 NO mA m YES FA=mAg FA 2000.19.8 196(N) FAmAg(N) (g: :9.8m/S 2) P F -2-1P=0.5(MPaF=766(N)766(N) 196776 P7 -2-1 NO FA F RS2H50 YES v [m/min] m [kg] -1 5 - -1-1.(RS2H50) -1-2.(RS2H63 -1-3.

CEx-OMB0075

Place where atmosphere containing con-ductive powder such as dust and iron chips, oil mist, salt, or organic solvent, or splashing cutting chips, dust and cutting oil (water , liquid) over the products. f. Place where the products are exposed to direct sunlight or radiated heat. g.

CEP1

d. , e. 6. , ,, 7. , , , , ,, , , () f. , g. ( ) h. , i. j. k. l. 8. , , 9. ,, 2. , 1. , , ,, 1. , , 2. , , 2. 3 , ,, , 3. , 4. ,, , , 1. , 3. , , 1. :12:0.15~1.0MPa 20:0.1~1.0MPa :0~60 4. , , , 2. ,, 5. 6. 1. , 5m 2. , 1. , 2. , 3. , ,, 1. , 2. , , 1. () 1. , 2. 145 CEP1, , 2. , 3. F.G.(), F.G. 3. 4. 4.

CEx-OMQ0010

a0~60 b25~85%RH c d e 5. f g. h i 6. j k L 2. 7. 8. 1. 9. 2. 10. 11. ()70% ()35% 1. 15% 1. 2. 3 3. () 1. 0.1~1.0MPa 0.3~0.5MPa 0~60 ()35% 2. ) 1. 1. 2. 2. 3. 1. 1. ( 2. 6 ) 3. 2. 50% 4. (6 ) 3. 5. 4. () 0.5 5. 1 2 3. F.G. 1. 4. 1 ISO VG32 1. 2. 1. 2. 3. 1. 2 1. 2. 2. 14.5mT CE2 1.5~2 15,000 18cm 3. 4. IP65 5.

Air Gripper for collaborative robots.

Gripping Force F (N) Gripping Point L (mm) Gripping Force F (N) Gripping Point L (mm) 7 3-3.

Electric Actuator / Slider Type 《 AC Servo Motor 》

The rubber back of the belt is softened and sticky. f. Crack on the back of the belt 41 - 7.6 How to detach and attach the dust seal band For the internal-check as the maintenance, the method of detaching and attaching the dust seal band is shown as the following. 1. Loosen the fixing bolts of end side of the Band holder.

Electric Actuator / Guide type 《 Battery-less absolute (Step motor 24VDC) 》

Rubber back of the belt is softened and sticky. f. Crack on the back of the belt -24- 3.5 Replacement of belt 1. After Screw is removed, "Pulley plate" is removed. 2.After screw is removedEnd cover and Grommet are removed, and Motor cover is lifted up. Screw Return plate Motor cover Motor cover Grommet Screw End cover 3.The screw[A] that is the fixation of "Motor" is loosened.

Electric Slide Table / High Precision Type 《 Battery-less absolute 》

Rubber back of the belt is softened and sticky. f. Crack on the back of the belt 21 - 4. Troubleshooting Alarms below are abstract of representative examples. For other alarms, see operation manual of controller. No.

Electric Slide Table / High Precision Type 《 AC servo motor 》

Rubber back of the belt is softened and sticky. f. Crack on the back of the belt 4. Troubleshooting Alarms below are abstract of representative examples.

High performance type Step Motor Controller (Servo/24 VDC)

Locations where strong magnetic or electric fields are generated. f. Locations where direct vibration or impact is applied to the product. g. Areas that are dusty, or are exposed to splashes of water and oil drops. h. Areas exposed to direct sunlight (ultraviolet ray). i. Environment at an altitude of 1000 meters or higher Heat radiation and withstand voltage will decrease.

JXCx-OMY0008

F Fieldbus P PLC Abbreviation of Programmable Logic Controller, a digital computer used for automation of electromechanical processes. Connection configuration of the Fieldbus network Expresses how each terminal and control components are connected. The typical topology is star type, linear type and ring type.

JXCx-OMY0006

F Fieldbus A unique address that identifies a device on a network. It is referred to as a logical address while the MAC address is known as a physical address. I IP address This is a physical address, which is uniquely assigned to any hardware device on a network. This address is permanently written to the device before shipment.

JXCx-OMY0004

F Fieldbus Allows a device to be configured for a PROFINET network, using PLC setting software. The file describes data exchange, device information and supported PROFINET features. G GSDML file A unique address that identifies a device on a network. It is referred to as a logical address while the MAC address is known as a physical address.

SFOD-OMT0009CN

(INx) (b)DRIVE ONNo.1(OUTx ) (c)BUSY ONINP OFF() (d)No.1 AREA ON(150mm ) (e)BUSY OFFINP ON(No.1 ) (f)No.2(INx) (g)DRIVEONNo.2((OUTx ) (h)AREA OFFBUSY ONINP OFF() (i)No.2 AREA ON(170mm ) (j)No.2 AREA OFF(130mm ) (k)BUSY OFFINP ON(No.2 ) -50mm No.1 ( 200mm1 150mm2 250mm) No.2 ( 100mm1 130mm2 170mm) No.1 No.2 No.

JXCx-OMT0001CN

1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 -72No.JXC-OMT0001CN-C 10.7 PLC PLC 1 2 3 PLC 40ms 10.8 3 EMG EMG OFFOFF( ) RESET RESET ON() HOLD HOLD ONHOLD RESET ,OUT OFF -73No.JXC-OMT0001CN-C 11. 11.1 EtherNet/IP 11.2 (1) --(a) (b) *ALARM ON *ESTOP ON (c) SVON ON (d) SVRE ON INP ON ALARM SVRE INP ON ESTOP ( ON SVRE ON 20 ) ON (e)SETUP ON *ALARM *ESTOP (f)

Step Motor Driver （ Pulse input type ）

Example) Step data of the controller setting kit [Normal mode] Speed Position Accel Decel PushingF T riggerL V PushingSp Moving F Area1 Area2 In posn No. Move mm/s mm mm/s2 mm/s2 mm/s mm mm mm 0 Fixed value Fixed value Fixed value Fixed value Fixed value 60 50 30 100 18.00 22.50 0.5 1 63 *1) Available only for driver's version V1.60 or more.

LEC-OM036xx

Locations where strong magnetic or electric fields are generated. f. Locations where direct vibration or impact is applied to the product. g. Areas that are dusty, or are exposed to splashes of water and oil drops. h. Areas exposed to direct sunlight (ultraviolet ray). 2. Do not use in an environment where the product is directly exposed to liquid, such as cutting oils.

LEC-OM034xx

B RATE switch B RATE the transmission rate of controller IF Nod address (X100) F : A Do not use 9 100 ~ 125 8 230.4kbps 1 ~ 99 7 : 2 Do not use 1 100 ~ 125 0 115.2kbps 1 ~ 99 Caution1: Set the controller IF communication speed at 115.2kbps to use the teaching box (LEC-T1-). Caution 2: Turn off the power supply in order to change the switch setting. 16 - 4. 2.