Air cylinder

Description Note 1 Rod cover 2A Head cover A For Basic type 2B Head cover B For Boss-cut type 2C Head cover C For Integral clevis type 3 Cylinder tube 4 Piston 5 Piston rod 6 Bushing 7 Seal retainer 8 Retaining ring 9 Bumper A 10 Bumper B 25 or largerThe same as bumper A 11 Rod seal 12 Piston seal 13 Wear ring 14 Bushing for clevis 15 Mounting nut 16 Rod end nut 17 Plastic magnet For CDM2

LFE-OMZ0012

1/2(15 A) 3/4(20 A) 1(25 A) Weight(Body) *5 Approx.

DOC1020530

Power must therefore be switched on when the servo motor is at a stop. (2) Servo-on Enable the servo-on with the following procedure. (a) Switch on main circuit power supply and control circuit power supply. (b) Transmit the servo-on command with the controller.

Auto Switch Guide Reed Switches/Solid State Switches For Rotary Actuators (Air Grippers) 1

When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.

Ionizer Nozzle type IZN10 Series IZS

Avoid using and storing this product in the following environments since they may cause damage to this product. a) Avoid using in a place that exceeds an ambient temperature range of 0 to 55C. b) Avoid using in a place that exceeds an ambient humidity range of 35 to 65% Rh. c) Avoid using in a place where condensation occurs due to a drastic temperature change. d) Avoid using in a place in

SI unit for EtherNet/IP TM

side and then B side in that order as shown in the figure a.

Safety Instructions

a) Use a device such as a water hammer relief valve to slow the valve's closing speed. b) Absorb an impact pressure by using a rubber material piping such as a rubber hose and an accumulator. c) Keep the piping length as short as possible. 1. Mount a switch by observing the proper tightening torque.

Uniaxial Electric Actuator Series LJ1

3000 a=1000 400 400 L3 mm L3 mm L3 mm a=2000 a=2000 a=2000 400 a=3000 a=3000 a=1000 a 200 200 200 L1 M1 0 2 4 6 8 10 0 5 10 20 15 0 5 10 15 Work load (W) kg Work load (W) kg Work load (W) kg Mounting position Model LJ1S10 LJ1S20 LJ1S30 Direction of load movement 30 150 300 a=500 a=500 a=500 a a=1000 a=2000 a=1000 20 100 200 a=2000 a=2000 a=3000 L1 mm L1 mm L1 mm M1 W 10 50 100 L1 10 30 20

HRX-OM-R028

range. 03Data field of a command is not normal.

25

Diaphragm Assembled in a clean room.

α PneuAlpha HARDWARE MANUAL

HOUR METER 19 Records the accumulated time an Output or Input signal has been ON SCHMITT TRIGGER 19 Turn an Input On at the High Value and Off at the Low Value (or vice versa) ZONE COMPARE 20 Compare a value to a range of values (Analog, Direct Set, or FB values) DISPLAY * Display Messages or Data on the LCD display OFFSET GAIN 22 Manipulate Analog Values; y = A/B*x + C; Set High and Low

PF2D

Avoid especially the application of pressure above specifications through a water hammer. a) Use a device such as a water hammer relief valve to slow the valves closing speed. b) Absorb impact pressure by using an accumulator or elastic piping material such as a rubber hose. c) Keep the piping length as short as possible. 7.

ITV

Then, a correct operation works until a vacuum pressure proportional to the input signal is reached, and a vacuum pressure is obtained which is always proportional to the input signal.

3 Port Direct Operated Poppet Solenoid Valve Series VKF300 1

Flow Characteristics/Weight C [dm 3/(sbar)] b Cv C [dm 3/(sbar)] b Cv 1 2 (P A) 2 3 (A R) Valve model Flow characteristics Weight (g) Operating pressure range (MPa) Port size Grommet DIN terminal 0.10 0.13 0.13 0.10 0.13 0.13 0.13 0.13 0.13 0.13 0.41 0.32 0.32 0.41 0.32 0.59 0.32 0.32 0.59 0.32 2 3 2 3 2 3 VKF33 VKF33 Y VKF33 E VKF33 V VKF33 W VKF334 VKF334Y VKF334E VKF334V VKF334W 0.67

PSE300.eng

Setting Switch output Fit Hook 1 on the base of the body on to the DIN rail, and press in the direction of the arrow to fix, as shown in Fig a. For removal, release the catch with a screwdriver in the direction of the arrow shown in Fig. b. Refer to the SMC website (URL http://www.smcworld.com) for more information about troubleshooting.

Series 11-MXJ Air Slide Table

Reed Auto Switch: D-A93 (mm) Stroke B A Stroke C Auto switch operating range Stroke Model 5 10 15 20 5 10 15 20 5 10 15 20 11-MXJ4 11-MXJ6 11-MXJ8 14 14 0.5 0.5 9 4 4 3 14 14 18 0.5 0.5 0.5 9 4 10 5 25 14 14 25 0.5 0.5 0.5 0.5 9 4 Solid State Auto Switch (Lead Wire, In-line Entry): D-M9 (mm) Stroke B A Stroke C Stroke Auto switch operating range Model 5 10 15 20 5 10 15 20 5 10 15 20

PFMB.eng

[L/min] PF-OMP0003-A

Clean Air Filter

Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.

High Precision Digital Pressure Switch, Series ZSE50F/ZSE60F, ISE50/ISE60

High Suction Vacuum Work 1 Work 2 Work n Max.A ON point OFF point Min.B Not adsorption Work 1 Work 2 Work n Atmosphere A B 4 A B 4 = A ON point Max.A: Maximum pressure value when work piece is vacuumed. Min.B : Maximum pressure value when work piece is not vacuumed.

ZISE40A.eng

Maintenance Bracket A or D(Model: ZS-24-A/ZS-24-D) Bracket B (Model: ZS-24-B) [01/N01 type] [W1/WF1 type] Operator How to reset the product after power cut or forcible de-energizing The setting of the product will be retained as it was before a power cut or de-energizing.