SMC Corporation of America
Elite Part Number Search
Search Results "IR1210-01B-R-A"

GF Cylinder suffix Port on top, cushion valve on the left A Nil A Nil N R H Without rod end nut Rod end nut With rod end nut Built-in Magnet Cylinder Model With cushion on both sides Port on top, cushion valve down Without cushion Presence of cusion If a built-in magnet cylinder without auto switch is required, there is no need to enter the symbol for the auto switch.

Release of residual pressure resistor is used in parallel with switching element or a C-R circuit (surge voltage suppressor) is used for protecting a For maintenance purposes install a system for releasing switching device because of the passing leakage voltage residual pressure. 6. Operation in a vacuum condition through the C-R circuit.

1 r !0 !2 w y e u t !6 i o !7 B !3 B section MU25 Spring extend w i !0 o !8 t !5 q !7 r e u !1 !2 !6 y !4 A B !

Do not use a load that generates surge voltage. Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if the surge is applied repeatedly. When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch having a built-in surge absorbing element. 8.

Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.

KNH-R02-100 KNH-R02-150 KNH-R02-200 1 1.5 2 R1/4 14 52 46 D H1 A L1 Reference dimensions after R thread installation Low noise nozzle with male thread: KNS (mm) thread L1 A Width across flats H1 D Connection Nozzle size Part no.

For the fitting with sealant R or NPT, first, tighten it by hand, then use a wrench appropriate for the hexagon flats of the body to tighten it a further two or three turns. For a tightening torque guide, refer to the table below. 2. Ordinarily, air is discharged from the bleed port (PE).

14 A B A 14 A B A B A 14 A B A 14 A B 3 2 A 14 U side D side D side U side 0 1 5 4 2 3 B 12 B 12 B 12 B 12 B 12 7 8 1 2 3 4 5 Valve stations EX600-ED4 1 set EX600-WEN1 1 set EX600-EU1 1 set SS5Y3-10S6WE72-05B-C6 (Type 10 5-station manifold base, Wireless EtherNet/IP) Negative common, M12 connector IN/OUT pin arrangement 1, I/O unit: 2 stations * SY3100-5U1 3 sets (2-position single part

A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty. outdoors or in a place exposed to direct sunlight. 2.

This is equivalent to a field in a radius of about 18 cm from a welding part using welding current of about 15000 amperes.

MY-SA 2 x G F E 2 x H A B C D Side support B MY-SB 2 x J A B C D A 61 70 87 B 75 84 105 C D E F G H J Part no.

B A B A B A B C D Normally closed (NC = b contact), solid state switch (D-F9G/F9H type) are also available.

R H Nil Rc NPT G Nil TN TF Rod boot If a built-in magnet cylinder without auto switch is required, there is no need to enter the symbol for auto switch.

A Wireless Remote can then be registered to the dummy area at a later time, without having to change the I/O map Dummy Remote E Export Function to save the configured values of a wireless unit by exporting them to a PC. F Fieldbus Network protocol to establish digital communication between an automated industrial system such as a measurement tool or manipulation tool and a PLC.

When a surge generating load such as a relay or solenoid is directly driven, use a type of switch with a built-in surge absorbing element. 4. Since the type of applicable fluid varies depending on the product, be sure to verify the specifications. The switches do not have an explosion proof rating. To prevent a possible fire hazard, do not use with flammable gases or fluids. 5.

XL1A16-2-101-XN1 Suffix for seal materials Seal material EPDM Barrel Perfluoro R Kalrez R Chemraz R VMQ FKM for PLASMA Combination No. 2101-80 70W 4079 SS592 SS630 SSE38 1232-70 3310-75 Symbol -XN1 -XP1 -XQ1 -XR1 -XR2 -XR3 -XS1 -XT1 Note 1) Barrel Perfluoro R is a registered trademark of MATSUMURA OIL Co.,Ltd. Kalrez R is a registered trademark of E.

Please check that each wire and cable is not broken. 6 Open the 3 (R) port. 7 Open the P2 port. 8 Input signal, and supply air to port 2 (A).