Clean Gas Filter Attached to product (2 pcs each) Regarding the TSJ fittings, after tightening the nut by hand, add another 1 1/4 to 1 1/2 turns with a wrench to seal the fitting. In case the fitting is re-installed after filter replacement, first tighten the nut by hand and add another 1/4 to 1/2 turns for sealing. Use the following parts as piping and fittings.
Table 1 Bonnet assembly/construction part number:1 Valve size Temperature specifications 16 25 40 50 Standard(5150) XLH16-30-1 XLH25-30-1 XLH40-30-1 XLH50-30-1 Note1) List the optional seal material symbol after the model number, except for the standard seal material (FKM: compound no. 1349-80).
Regarding the TSJ fittings, after tightening the nut by hand, add another 1 1/4 to 1 1/2 turns with a wrench to seal the fitting. In case the fitting is re-installed after filter replacement, first tighten the nut by hand and add another 1/4 to 1/2 turns for sealing. Use the following parts as piping and fittings.
Attached to product (2 pcs each) Regarding the TSJ fittings, after tightening the nut by hand, add another 1 1/4 to 1 1/2 turns with a wrench to seal the fitting. In case the fitting is re-installed after filter replacement, first tighten the nut by hand and add another 1/4 to 1/2 turns for sealing. Use the following parts as piping and fittings.
T Conduit terminal Refer to the table (1) given below for availability. Rated voltage 3 2 1 110 VAC 50/60 Hz 200 VAC 50/60 Hz 100 VAC 50/60 Hz Model Port size (Rc 1/4) (Rc 3/8) (Rc 1/2) (Rc 3/4) (Rc 1) 02 03 04 06 10 2232 2232 2242 2352 2362 4 5 6 7 8 9 220 VAC 50/60 Hz 24 VDC 12 VDC 240 VAC 50/60 Hz 48 VAC 50/60 Hz Other (Please contact SMC for inquiry.)
They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC)*1) , and other safety regulations. *1) ISO 4414: Pneumatic fluid power -General rules relating to systems. ISO 4413: Hydraulic fluid power -General rules relating to systems. IEC 60204-1: Safety of machinery -Electrical equipment of machines.
Regarding the TSJ fittings, after tightening the nut by hand, add another 1 1/4 to 1 1/2 turns with a wrench to seal the fitting. In case the fitting is re-installed after filter replacement, first tighten the nut by hand and add another 1/4 to 1/2 turns for sealing. Use the following parts as piping and fittings.
2.4 0.60 0.12 2.8 1 4 VFS Double check VZS3650 420 32 or less 0.43 1.2 1.1 1 4 VS4 Note 1) Min. operating cycle is based on JIS B 8375 (One time per 30 days).
1 1 2 5 2-1. 5 2-2. 5 2-2-1. 5 2-2-2. 5 2-2-3. 6 2-3. 6 3 3-1. 7 3-2. 7 4 4-1. 8 4-2. 8 4-3. 8 5 5-1. 9 5-2. 10 5-3. 10 6 6-1. 11 6-2. 12 CEP1B12 13 CEP1B20 14 , 1 ,, , ,ISO4412 *1)JIS B8370 *2) ,, , ,, *1) ISO 4414 Pneumatic fluid power-Recommendations for the application of equipment to transmission and control systems. *2) JIS B8370
Caution How to Use DIN Terminal Precautions 1. Disassembly 1) After loosening the screw (1), then if the housing (2) is pulled in the direction of the screw, the connector will be removed from the body of equipment (solenoid, etc.). 2) Pull the screw (1) out of the housing (2). 3) On the bottom part of the terminal block (3), theres a cut-off part (9).
M3 hexagon screw Tightening torque 0.6 Nm 1 1 1 1 0 1 62 The technical document states detail troubleshooting information can be found on the SMC website (URL http://www.smcworld.com) 1 1 1 1 1 1 63 *: Thread size: M330 If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation.
MODEL / Series / Product Number JMHZ2-16D-X7400B Contents Safety Instructions . 2 1. List of included items . 4 2. Parts description of the air gripper . 5 3. Product Specifications . 6 3-1. How to order . 6 3-2. Specifications . 6 3-2. Gripping force . 7 3-3. Gripping point . 8 3-4. Dimensions (when the cover and attachment are mounted) . 9 3-5. Connector and pin layout . 9 3-6.
Start up procedure / Connecting to a computer . 5 2. 1 Preparation . 5 (1) Confirmation of product . 5 (2) Wiring . 5 (3) Installation of the Card Motor . 6 (4) Prepared and wired by the user. . 7 (5) Software installation . 7 2. 2 Controller settings . 8 (1) Start the setup software . 8 (2) Basic Parameter Setup . 9 (3) Step data setting . 9 3Start up procedureTest operation using a computer
Recommended tightening torque (Nm) Thread size 1/4 3/8 1/2 Torque 12 to 14 22 to 24 28 to 30 -9- (2) Do not apply torsion or bending moment other than the weight of the product itself.
Construction (2) VHK2A(R) VHK3A(R) (9) (4) (1) (5) (3) (11) (10) (7) (8) (6) No.
Read and understand this operation manual carefully before assembling, operating or providing maintenance to the product. 4 Display LED diagnostic display. 0 0 0 0 0 0 #0 Switch setting part Configures the MAC ID/communication speed. 5 #1 0 0 0 0 0 1 0 #2 0 0 0 1 0 : : : : : : : Solenoid valve power supply 24 VDC 1 1 1 1 #62 1 0 24 VDC 1 1 1 1 #63 1 1 The default setting is all switches ON
135 180 4-11 225 (266) (60) AIR VENT G 1/4 q q A (43) OUT IN e e 150 r B t 120 327 188 (519) w w 84 OUT 2-R 1 r IN 53 DRAIN G 1/4 Note Parts list Dimensions (mm) A B No.
INDEX 1. Safety Instruction .2 2. Outline.6 3. How to Order.7 4. Specification.7 5. Mounting .7 5-1. Electrostatic sensor installation.7 5-1-1. Sensor head installation.7 5-1-2. Installation of the sensor amplifier.8 5-2. Circuitry and wiring chart.9 6. Performance.10 6-1. Output signal.10 6-2. Detection range.11 6-3. Cautions on installation .11 6-4. Timing chart .12 7.
M 1 2 x 1 Cable connection threads suP (1) 2-Ro(PT) 114,318, 1/2 Port size Mounting hole L-bracket tNt-398-0-6 (optional) 2-Rc(PT) 1/4,3/8, 1/2 SUP port, OUT port Eleclno-Pltoulnalic Relulatnn rTUz000/3 lt'iler ilile $ruciliciliotts 2 through I station manifold.
Y 3 X 3 ZZY 45 J 1 U Note 1) With ejector Enter the following together with the manifold number: 1. Part No. of solenoid for SY3000/SX3000 2.