MLGC Wiring Setting and Adjustment OFF OFF OFF OFF OFF (3)When the mark B of the connector has been turned 180 degrees (1/2 turn), wiring is completed. Confirm that the connection is not loose. If turned too far, it will become hard to remove the connector. (2)Align the mark C on the unit and insert the connector into the unit vertically.
(default setting) Number of occupied valve 8 outputs Number of occupied valve 16 outputs Number of occupied valve 24 outputs Number of occupied valve 32 outputs Configuration X10 2 0 9 0 0 Mark C on the unit Mark B at cable end Mark A at cable end : : Address (1) Setting of the terminal resistor X1 Content 3 4 1 2 5 0 9 1 0 8 7 : : Content 9 6 5 x10 x1 0 5 4 1 2 3 0 (default setting) Node
P 2-TC TD D I E 0 -0.05 0 -0.05 E AL TE 2-TC K F TA DL2 TF TG A S + Stroke H NA F ZZ + Stroke Section TA With non-locking type manual override (suffix N) With locking type manual override (suffix L) HN HR MO RF WL WL KA 0.1 C 8-J NA (mm) Stroke range Bore size (mm) A AL B1 C D DL2 E F GA GB H H1 HR HN (max.)
C [Dry air] of the Model Selection Guide of Air Preparation Equipment on the SMC website.
wire Diagnostic indication (2-color indication) PLC (B59W) B59W Grommet G79 H7A1 H7A2 H7B H7C H7NW H7PW H7BW H7BA H7NF 3-wire (NPN) IC circuit 5 V, 12 V 3-wire (PNP) Grommet K79 K79C 2-wire 12 V Connector Relay, PLC 3-wire (NPN) IC circuit 24 V Diagnostic indication (2-color indication) 5 V, 12 V 3-wire (PNP) Grommet 2-wire Water resistant (2-color indication) 12 V 4-wire (NPN) With
Construction and Outer dimensions 1 Atm , vent port Bonnet assembly (maintenance part) (inc. each part excluding body, external seal and accessory) Bonnet (material A6063) 6 External seal (maintenance part) 3 Vacuum pump side Valve seal (maintenance part) 2 Valve (material SUS304) 5 Body (material A6063) 4 Chamber side E C A A B D Dimensions [mm] Model A B C D E XLJ-25 50 139 111 48 44 (54
3 Port Air Operated Valve Series VZA200/400 Fluid Air 1 2 1 2 VZA4 2, 4 4 1 2 1 2 VZA2 2, 2 4 1 2 1 2 VZA4 2, 4 4 1 2 1 2 Operating pressure range (MPa) 0.1 to 1.0 0.15 to 1.0 VZA2 2, 2 4 0.1 to 1.0 0.15 to 1.0 Pilot pressure range (MPa) Impact/Vibration resistance (m/s2) Note) 150/50 Operating pressure Pilot pressure Note) Impact resistance: No malfunction from test using drop impact tester
Wiring 3 4 1 2 (3)When the mark B of the connector has been turned 180 degrees (1/2 turn), wiring is completed. Confirm that the connection is not loose. If turned too far, it will become hard to remove the connector. (2)Align the mark C on the unit and insert the connector into the unit vertically. If they are not aligned, the connector cannot be joined properly.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
Fluctuation of flow rate at the downstream side Set the pressure again. 2 The set pressure increases or decreases as time passes. Aging deterioration of the regulator Set the pressure again. Due to problem 2. Refer to problem 2. 7 Repeatability accuracy is bad. Due to problem 1. Refer to problem 1. Leakage due to deterioration of the rubber part. Consult SMC.
with a warning tag. 01 02 03 04 06 10 1/8 1/4 3/8 1/2 3/4 1 Body size 2 3 4 5 1/8 3/8 1/2 1 SMC Interface part is required if attached to a modular FRL.
0 @2 O-ring C Bumper Urethane NBR !1 @3 Nickel plated Electroless nickel plated Reinforcement ring Hexagon socket head cap screw A Carbon steel Carbon steel !2 @4 Replacement Parts: Seal Kit Bore size (mm) Kit no. Contents 40 MGF40-PS Items !
Red flashing Mark C on the unit Seal cap (2 pcs.) Fitted to unused connectors. (BUS OUT and PCI) 12 Red/green flashing alternately Detect a communication error between SI unit and I/O unit. Assembly SI unit has failed. Red ON Connector pin assignment The power supply voltage for control and input is properly.
Warning: 1 2 1 2 Green ST(M) LED is flashing. 1 TD+ Either of the following conditions: The valve ON/OFF counter has exceeded the set value. The valve is short circuited or disconnected. Red ST(M) LED is flashing. 2 RD+ TD3 DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. (2)Add more I/O units.
PLC that cannot use a 2-wire type. The resin housing can be discolored due to the operating environment.
Power cable 1 Brown Power supply Vcc 2 White NC 3 Blue GND 4 Black Monitor output Signal cable 1 Brown Input signal 1 2 White Input signal 2 3 Blue Input signal 3 4 Black Input signal 4 5 Gray Common Common is no polarity.