Trimmer Auto Switch Take measures against freezing when operating at 5C or less. Mounting and Adjustment Caution 1. Do not drop or bump. Do not drop, bump or apply excessive impacts (980 m/s2 or more for sensor unit and 98 m/s2 or more for amplifier unit) while handling.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals or equipment malfunction. Therefore, take appropriate measures to prevent freezing. For compressed air quality, refer to the SMC Best Pneumatics No. 6 catalog. 5.
Low temperature operation 1) The valve can be used in an ambient temperature of not less than 5C.
Specifications Grade 1 Note 1) Particulate generation grade Air Fluid Series KPQ Brass (electroless nickel plated) Release button: Light gray 1MPa Note 2) Maximum operating pressure (20C) 100kPa Operating vacuum pressure 3MPa Proof pressure (20C) 5C to 60C Ambient and fluid temperature JIS B0203 (taper threads for piping) Threads Note 1) Refer to particulate generation grade classifications
Water 15% Ethylene Glycol Aqueous Solution Physical property value Physical property value Temperature Density r [kg/L] Specific heat C [J/(kgK)] Current unit system Density r [kg/L] Specific heat C [J/(kgK)] Current unit system Weight volume ratio c [kgf/L] Specific heat C [cal/(kgfC)] 5C 1.00 4.2 x 103 1.00 1 x 103 Weight volume ratio c [kgf/L] Specific heat C [cal/(kgfC)] 5C 1.02 3.91
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals or equipment malfunction. Therefore, take appropriate measures to prevent freezing. For compressed air quality, refer to the SMC Best Pneumatics No. 6 catalog. 5.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals or equipment malfunction. Therefore, take appropriate measures to prevent freezing. For compressed air quality, refer to the SMC Best Pneumatics No. 6 catalog. 5.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals or equipment malfunction. Therefore, take appropriate measures to prevent freezing. For compressed air quality, refer to the SMC Best Pneumatics No. 6 catalog. 5.
Tightening Torque for Piping VK300 series can be used down to -5C. VK3000 series can be used down to -10C. Connection thread Proper tightening torque (Nm) Rc1/8 3~ 5 5 VK300**-OMH0002-C VK300/3000 Series Precautions for 3/5 Port Solenoid Valve 3 Be sure to read before handling. Piping Air Supply 4. Piping to products 1.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals or equipment malfunction. Therefore, take appropriate measures to prevent freezing. 5) Precautionary measures against condensation Moisture condensation can occur inside pneumatic systems due to a drop in temperatures caused by the piping or operating conditions.
Take measures to prevent freezing, since moisture in circuits will freeze at or below 5C, and this may cause damage to seals and lead to malfunction. Refer to SMC's "Air Cleaning Equipment" catalog for further details on compressed air quality. 15 Series MGF/Specific Product Precautions Be sure to read before handling.
Note 3) Temperature conditions: at 20C (5C), in other cases, 6C F.S.
OFF 1 5C 3 Check the effect of ambient temperature. Please review the setting value. There may be causes such as large load fluctuation and flow rate fluctuation. Please review the setting value.
90F (32C) Air-cooled condenser fan Cooling valve Heating valve Power supply: 200 VAC/50 Hz Circulating fluid flow rate: Rated flow Existing model (Pump heat input only) Heating valve control Circulating fluid: Water 0 50 100 150 200 250 300 External piping: Bypass piping Elapsed time [Minute] Temperature stability 1.8C [1.0F] Cooling capacity10 kW/15 kW Set temperature range 41 to 95F [5C
Moisture in circuits can freeze at 5C or below, causing damage to Orings, and malfunction. Consider measures to prevent freezing. The installation of an air dryer is recommended to remove drainage and moisture from circuits. Furthermore, even though the ambient temperature range remains within specifications, do not operate in locations where there are abrupt temperature changes. 2.
Test temperature: 20 5C Relative humidity: 65 5% 5. Do not use fluids other than specified. The only fluid that can be used is air. Back page 2 Two Hand Control Valve/Precautions 2 Be sure to read before handling. Handling of One-touch Fittings Lubrication Caution Caution 1.
It is possible to operate this valve in extreme temperature, as low as 5C. Take appropriate measures to avoid the freezing of drainage, moisture, etc., in low temperatures. This product is universal porting type. N.C type, N.O. type, devider type and selector type can be used. 5 VT315-OMH0002-D VT315 Series 3 port solenoid valve/ Precautions (3) Be sure to read before handling.
Take measures to prevent freezing, since moisture in circuits will be frozen under 5C, and this can cause damage to seals and malfunction. Maintenance Warning 1. Perform maintenance according to the procedure indicated in the instruction manual. Improper handling can cause malfunction and damage of machinery or equipment. 2. Removal of equipment and supply/exhaust of compressed air.
OFF 1 5C 3 Check the effect of ambient temperature. Please review the setting value. There may be causes such as large load fluctuation and flow rate fluctuation. Please review the setting value.
Water 15% Ethylene Glycol Aqueous Solution Physical property value Temperature Density [kg/L] Specific heat C [J/(kgK)] Conventional units Physical property value Temperature Density [kg/L] Specific heat C [J/(kgK)] Conventional units Weight volume ratio [kgf/L] Specific heat C [cal/(kgfC)] 5C 1.00 4.2 x 103 1.00 1 x 103 Weight volume ratio [kgf/L] Specific heat C [cal/(kgfC)] 5C 1.02