SMC Corporation of America
Elite Part Number Search
Search Results "RS2H50-30TM-DC"

Caution Manifold Mounting When the DC power supply is shut off, by the emergency breaking circuit for example, valve misoperation may occur due to surge voltage produced by other electrical parts (such as electromagnetic coils).

Supply 24 V DC to each of them. Power can be supplied from a single power supply or from separate power supplies. It is not necessary to connect the SW power supply when not using an input block. : When a single power supply is used, the voltage range of each power supply should be noted. SW power is supplied to the sensor connected to the input block.

Open the cover and set the address using an AS-Interface address programming device and DC power jack cable etc. (PEPPERL + FUCHS: VAZ-PK-V1-Cinch, SIEMENS: 3RK1901-3HA00 etc.) The Address assignment range is 1 to 31. The address can be set regardless of connecting order, but it is not possible to set address overlap. The address at shipment from the factory is 0.

Polarity Excessive tightening may damage the thread portion When connecting power to a solenoid valve with a DC specification and a light or surge voltage suppressor, check for polarity. If there is polarity, take note of the following.

Wiring Meaning Connector pin number Wiring colour 1 Brown Power supply DC(+) 2 White Analogue current output/Analogue voltage output 3 Blue Power supply DC(-) 4 Black IO-Link/Switch output (C/Q) Wiring specifications M8 Connector pin assignment M12 Connector pin assignment -11No.D-S-OMU0002-A Setting Initial settings are as follows: Switch output: Low (NPN = ON, PNP = OFF), Analogue output

Power supply (Valve) 24V DC -5% to +10% Current consumption Communication power supply 0.1A or less (24VDC) Enclosure IP20 Weight 80g or less CompoBus/S system specification Item Specification Applicable PLC OMRON Coop.

Therefore, when it is continuously energized or the energized period per day is longer than the de-energized period use a DC specification valve. For applications such as mounting a valve on a control panel, incorporate measure to limit the heat radiation so that it is within the operating temperature range.

Keep residual voltage leakage to 3% or less of the rated voltage for DC and 8% or less of the rated voltage for AC. Mounting Caution All models 1. In high humidity environments, keep the valve packed until the time of installation. 2. For models with switches, secure the lead wires so that they have sufficient slack, without any unreasonable force applied to them. 3.

DC output voltage of product is reduced. 1 Serial communications RS-232C / RS-485 RS-232C, RS-485 RS-232C ERR11 DC power supply failure Stop When no input is made within 1 minute regardless of setting mode, the A Power switch H Communication connector The fans at the power supply stops.

When a valve is used for switching a vacuum, take DC coil: 3% or less of rated voltage AC coil:15% or less of rated voltage measures to install a suction filter or similar to prevent external dust or other foreign matter from entering inside the valve. In addition, at the time of vacuum adsorption, be sure to vacuum at all times.

HECR002: 100 to 240VAC HECR004: 100 to 240VAC HECR006: 100 to 240VAC HECR008: 100 to 240VAC HECR010: 200 to 240VAC DC output voltage of product is reduced. 2) Confirm that the heat sink and panel are free from dust.

DC 24V power Power supply plug EMG supply C24V Wiring 24V 0V M24V 0V Electrical wire entry 4 - 1.2 Controller setting software version 1. Installation of software With the controller setting software CD-ROM, install the communication unit software, following the Software Installation procedure (PDF) 2.

If a control power supply is provided, DC specification has polarity. Follow the indication shown on the end of lead wire. 4. A wire for wiring should be 0.5 to 1.25mm2 or more as reference. 5. Give enough curvature to the lead wire not to have excessive force when it is fixed. 6. Fluid containing foreign matters and oil will cause malfunction and sealing failure.

Load voltage Auto switch model Lead wire length (m) Special function Indicator light Flexible (2) Pre-wire (1) Wiring (Output) Type Solid state switch Electrical entry Applicable load Electrical entry lead wire (-61) 0.5 (Nil) 3 (L) In-line 5 (Z) connector DC AC Perpendicular 3-wire (NPN) Y69A Y59A IC circuit 5 V 12 V Y7P Y7PV Grommet Relay, PLC 3-wire (PNP) Standard Yes 24 V Y69B Y59B 12

PLC: Programmable Logic Controller Lead wire length (m) Auto switch model Flexible lead wire (-61) Load voltage Special function Electrical entry Applicable load Pre-wire connector Indicator light Wiring (Output) Type Electrical entry 0.5 (Nil) 3 (L) 5 (Z) AC DC Perpendicular In-line 3-wire (NPN) M9NV M9N 5 V 12 V IC circuit Standard 3-wire (PNP) Solid state switch M9P M9PV M9B M9BV 2-wire

Please contact SMC if an inverter welder or a DC welder will be used. When a magnetic body surrounds the cylinder as shown in the figure below (including when the magnetic body is only on one side of the cylinder), the movement of the auto switch may become unstable, so please contact SMC. 12 to 16 32 to 63 Magnetic body (Iron plate, etc.)

Auto switch Lead wire* (m) Without auto switch (Built-in magnet) Load voltage Indicator Style Special function Wiring (Output) Electrical entry Auto switch model Applicable load 0.5 () 3 (L) 5 (Z) None (N) DC AC * Refer to the left table for selecting applicable auto switches. 3 wire (NPN) C76 C73 C80 B53 B54 B64 C73C C80C A33A A34A A44A B59W H7A1 H7A2 H7B H7C G39A K39A H7NW H7PW H7BW H7BA

The graphs are based on operation using an SMC DC power input type driver with halfstep energization.

Load voltage Auto switch model Lead wire length (m) Special function Indicator light Flexible (2) Pre-wire (1) Wiring (Output) Type Solid state switch Electrical entry Applicable load Electrical entry lead wire (-61) 0.5 (Nil) 3 (L) In-line 5 (Z) connector DC AC Perpendicular 3-wire (NPN) Y69A Y59A IC circuit 5 V 12 V Y7P Y7PV Grommet Relay, PLC 3-wire (PNP) Standard Yes 24 V Y69B Y59B 12