I Bore size CV Rod extended/retracted when energized 20 25 32 40 20 mm Piping 25 mm Built-in Magnet Cylinder Model Screw-in type Nil F Nil B MVGQ Rod extended when energized 32 mm Built-in One-touch fitting If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch.
) 2 x 5.5 Without spacer With spacer 2 x M5 thread depth M 15 15 Spacer Grommet: GS Flat terminal: F Conduit: C 280 G F F G 11 300 G F Terminal part Flat terminal connector 11 23 9 H C 15 6.5 H C H C G1/2 Terminal: T DIN terminal: D F G Applicable cable O.D.: 6 to 12 F G Width across flats 22 G1/2 32 (44) H 31.5 25 C H C G1/2 J J Dimensions [mm] Model A B Bs C D E F L M P [inch] Grommet:
XT661-2A: F = f x (1/t) = 0.8 x (1/2) = 0.4 N XT661-4A: F = f x (1/t) = 3.8 x (1/2) = 1.9 N XT661-6A: F = f x (1/t) = 5.9 x (1/2) = 2.95 N XT661-8A: F = f x (1/t) = 7.5 x (1/2) = 3.75 N XT661-10A: F = f x (1/t) = 14.4 x (1/2) = 7.2 N 9700 g 9700 x 9.8/1000 = 95.06 N XT661-10A: Temporary lifting force 11.2 N < Workpiece mass 9700 g (95.06 N) 3) Confirm the relationship temporary lifting force
) is included as an accessory for the thread symbol F.
Calculation of applied lateral load The lateral load F equals the total load of the workpiece. Thus, F= 5 x 0.05 x 9.8 = 2.5 (N) 1. Calculation of applied lateral load F F = N m g (N) = 0.2 x 10 x 0.1 x 9.8 = 2.1 (N) CC 70 Lateral load F (N) RB 60 0.4 MPa 50 J 40 2.
h 9 l 16 2 x 4-J N F H + Stroke A K ZZ + 2 strokes S + Stroke H A K F N C B With rod boot In the case of w/o air cushion, it comes with rubber bumper.
Number of fingers and therefore, mg F 2 x With "a" as the safety margin, F is determined as follows: mg F = x a 2 x When = 0.2 When = 0.1 mg F = x 4 2 x 0.2 mg F = x 4 2 x 0.1 = 10 x mg = 20 x mg 10 x workpiece weight 20 x workpiece weight (Note) Even in cases where the coefficient of friction is greater than = 0.2, for safety reasons, SMC recommends selecting a gripping force which
Number of fingers and therefore, mg F 2 x With "a" as the safety margin, F is determined as follows: mg F = x a 2 x When = 0.2 When = 0.1 mg F = x 4 2 x 0.2 mg F = x 4 2 x 0.1 = 10 x mg = 20 x mg 10 x workpiece weight 20 x workpiece weight (Note) Even in cases where the coefficient of friction is greater than = 0.2, for safety reasons, SMC recommends selecting a gripping force which
will not drop are F F 2 x F > mg mg Number of fingers Gripping force at least 10 to 20 times the workpiece weight The "10 to 20 times or more of the workpiece weight" recommended by SMC is calculated with the safety margin of a = 4, which allows for impacts that occur during normal transportation, etc. and therefore, mg F > 2 x With "a" as the safety margin, F is determined as follows:
Operating pressure: 0.4 MPa Model Selection Illustration When gripping a workpiece as in the figure to the left and with the following definitions, F: Gripping force (N) : Coefficient of friction between attachments and workpiece m: Workpiece mass (kg) g: Gravitational acceleration (= 9.8 m/s2) mg: Workpiece weight (N) F F the conditions under which the workpiece will not drop are mg F F
VCKK1209-02F VCKK1008-02F VCKK1075-02F VCKK0806-02F VCKK0604-02F Symbol F G H J K Part no.
Size 40 L L 2 K G1 0 0.030 F D B 4 K N V1 Body (B) T V2 M S Body (A) h Key dimensions L1 b C G2 J F h (h9) L1 b (h9) Model L 2 x R A CRB2B;40 4 0 0.030 4 0 20 E 0.030 CRB2B=10-=S CRB2B==-=SE/DE
Flange (F, G) [mm] Bore size [mm] Part no.
J D 300 J F G1/2 25 25 Width across flats H Width across flats H K K C C Port size 3 x P Port size 3 x P E E B1 A A B2 B2 B1 Conduit terminal: T DIN terminal: D F J D Cable 6 to 12 F M J 34 G1/2 D 25 Width across flats H Width across flats H N 44 K K C C M Port size 3 x P Port size 3 x P E E A A B2 B2 B1 B1 G1/2 With bracket T 4 Q (mm) Grommet Conduit DIN terminal Electrical entry (AC/Class
[F 7] Setting of fine adjustment of display value 0% 1 s Mounting and Installation Manual [F 8] Setting of auto-preset Display to show the unit specification OFF [F 9] Setting of power saving mode 1 s Installation Mounting Mount the optional bracket and panel mount adapter to the Pressure switch.
G Rear flange F Front flange L Foot C Male rear clevis D Female rear clevis 1.8-29
T T V V 2-Rc P Cushion adjustment screw 4-J GA F GA A MA a A MA a Air release R (max.)
Seal kits consist of items 12, 13, 14 and 16 contained in one kit, and can be ordered using the order number for each respective tube bore size. 13 Series MB1W Standard Type MM MM G VW 2-Rc(PT)P G Cushion valve Port Basic type/(B) E D D E e MB Effective thread Effective thread 13 f 16 h 9 2 x 4-J N F l H + Stroke A K ZZ + 2 strokes S + Stroke H A K F N C B With rod boot MM 2-Rc(PT)P G G