Series CQ2 Do not drop or bump. 5. Do not allow short circuit of loads.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 5. Do not allow short circuiting of loads.
Do not use in an environment with temperature cycles.
Do not use the product in an environment subject to a temperature cycle. It will cause failure of the gateway unit or its peripheral devices. 14. Do not use in a place where surges are generated.
Do not use the switches in locations where static electricity would be problematic; it may result in system failure and trouble. Section A (Lever) Do not attempt to insert or pull out the connector from the switch while the power is on. Otherwise, it may cause switch output malfunction.
11 22 52 100.5 8 CLQ H GR H1 I N NA K L P PG PH PL PW RR S U Z ZZ MM NN Bore size (mm) 1/8 1/8 1/8 1/4 20 4 22 19.5 20 38 9 127 14 198 207 41 5 28 5 30 M8 x 1.25 15 24 M20 x 1.5 MLGP 25 7 27 24 24 41 9 137 14 212 221 45 6 33.5 5.5 30 M10 x 1.25 15 30 M26 x 1.5 32 7 27 24 24 41 9 139 14 214 223 45 6 37.5 5.5 30 M10 x 1.25 15 34.5 M26 x 1.5 RLQ 40 7 29 24 24 41 11 167 18 256 267 50 8 46.5
21 58 25 to 800 109 57 29 14 136 11 3/8 39 13 M10 x 1.25 35 14 88 37 104 40 0.15 0.18 11 10 21 45 25 to 800 118 65 29 14 57 3/8 42 136 11 M10 x 1.25 13 95 37.5 14 36 104 50 14 27 10 145 76 52 25 to 800 35 18 46 150 60 1/2 M10 x 1.25 18 11 115 45 17 43 116 63 18 27 90 63 10 165 25 to 800 41 156 71 19 52 20 14 1/2 M12 x 1.5 50 19 132 43 114 0.20 80 18 80 11 22 110 25 to 1000 190 74 45 20 166
Made to Order Symbol 3 Model with 40 mm-pitch emitter cartridges X15 16 36 L 14 14 Install the emitter cartridges at a 40 mm-pitch. (Standard: 80 mm-pitch) Maintenance detection level selection switch KJH04-M5-X34 30 20 Position Detection Switch Flow Sensor Pressure Control Pressure Sensor Balance adjustment trimmer 14 19 20 16 Note) The maximum bar length is 1260 mm.
(mm)
Do not wipe out the grease in the sliding part of the air cylinder.
Please do not use it in this fashion. 3. An F.R.L. unit shipped from the plant has its model number labeled. However, components that are combined together during the distribution process do not have a label on them. Air Supply Caution 1.
Precautions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Precautions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Pressure Do not use it in the vacuum state, which is substantially different from the atmospheric pressure (above sea level) and in the atmosphere under being pressurized. 10-18-14 13 Shock Absorber: Short Type Series RBQ Precautions Be sure to read before handling. Refer to pages 10-24-3 to 10-24-6 for Safety Instructions and Actuator Precautions. Mounting Maintenance Caution 3.
14 16.2 16.2 4 4 MK(2) Note) L, LL and S dimensions of RBL(C)1007/1006 are different from those of RB(C)1007/1006.
Do not operate a cylinder with its bumper bolt removed. If the bumper bolt is removed, the piston hits the head cover, causing damage to the cylinder. Therefore, do not use a cylinder without a bumper bolt. 2. The piston rod must be retracted when mounting the cylinder.
Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. 12. Do not use body A and/or elbow body for applications involving continuous rotation. Mounting Body A and the fitting section may be damaged. Warning 1.
(page 14-19-14) Operating Environment Caution 1. Do not use at temperatures (fluid or ambient temperatures) higher than the prescribed operating conditions. Resin is used in the membrane module, and it can be damaged by operation at high temperatures.
14 15 4 4 4.5 4 4.5 14 14 17 16 18 Since this is a guideline including hysteresis, not meant to be guaranteed.
Do not mount this kit on other products. Carefully read the procedure manual included with this kit before performing the installation.