LEKF-OMZ0035 Dedicated grounding should be used. Grounding should be to a D-class ground. (Ground resistance of 100 or less.) 3. Grounding should be performed near the actuator to shorten the grounding distance. 4. The cross-sectional area of this wire shall be a minimum of 2 mm2. 5. Avoid common grounding with other devices.
(Tightening torque should be 0.5 to 0.7Nm.)
Grease pack part number: GR-S-010 (10g), GR-S-020 (20g) 3-3. Replacement Parts Refer to the catalog the parts that can be replaced. Warning 1. Maintenance should be performed according to the items above. Improper handling can cause damage or malfunction of equipment and machinery. 2. Removal of equipment, and supply/exhaust of compressed air.
This calculation can be easily made using the SMC Pneumatics CAD System.
Grease pack part number: GR-S-010 (10g), GR-S-020 (20g) 3-3. Replacement Parts Refer to the catalog for the parts can be replaced. Warning 1. Maintenance should be performed according to the items above. Improper handling can cause damage or malfunction of equipment and machinery. 2.
Grease pack part number: GR-S-010 (10g), GR-S-020 (20g) 3-3. Replacement Parts Refer to the catalog the parts that can be replaced. Warning 1) Maintenance should be performed according to the items above.
The separate temperature sensor needs to be prepared separately by the customer. 1000 meters.
Position where light turns ON Position to be secured Position to be secured It is recommended that gripping of a workpiece be performed close to the center of the finger stroke.
Reduction rate Series CQU CAT.ES20-198A Auto switch can be mounted without removing a support bracket. Easy maintenance Easy maintenance Auto switch can be mounted without removing a support bracket. Seals can be replaced easily just by removing the retaining rings. Auto switch A small type of auto switch can be mounted from 4 directions.
Note 2) Pressure switch cannot be mounted later on non plug-in type.
The resulting impact cannot be absorbed easily, the stroke position cannot be maintained, and faulty operation may result. 5. Lubrication The bearing can be used in an oilless state, but when you are going to oil the bearings, do so by using a nipple so that no foreign matter will be mixed. For the grease, we recommended using high-quality lithium soapbased grease no. 2. 6.
Note 3) The non plug-in type cannot be mounted afterwards.
If the direction is not correct, it will be impossible to obtain the specified holding force. The flatness of the cylinder mounting surface should be 0.2 mm or less, and the product should be mounted so that it can operate smoothly over the full stroke with the minimum operating pressure (0.18 MPa or less).
If the tightening torque is exceeded the mounting screws may be broken. IP67 protection cannot be guaranteed if the screws are not tightened to the specified torque. Never mount a product in a location that will be used as a foothold. The product may be damaged if excessive force is applied by stepping or climbing onto it.
Grease pack must be ordered separately as it is not included in the seal kit. Grease part no.: GR-S-010 (10 g) Length of plug connector lead wire The standard length of the plug connector with a lead wire is 300 mm, but other lengths are available as follows.
Be sure to contact SMC regarding disassembly or repair, etc. D-X Individual -X 779
Note 3) The non plug-in type cannot be mounted afterwards.
If the product is only fixed/supported by the bolts, they may deflect or break. (4)Consult with SMC if the rod end deflection or non-rotation accuracy need to be guaranteed. (5)This product is not designed to be used in a clean room.
The IODD file can be downloaded from the URL below.
Grease pack part number: GR-S-010 (10g), GR-S-020 (20g) Warning 1) Maintenance should be performed according to the items above.