Do not apply strong impact or an excessive moment while mounting the product or a workpiece. LEC SS-T LEC Y LEC Y If an external force over the allowable moment is applied, it may cause play in the guide or an increase in the sliding resistance. 3.
Note) Please contact SMC when using an individual EXH spacer assembly, an individual SUP spacer assembly, an adapter plate assembly, or an interface regulator on 41P and 43P types.
Note) Since the electrical entry is LO, select an appropriate connector assembly part no.
Mixed single and double wiring is available as an option.
Never use in an atmosphere of explosive gases. The structure of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated. Auto switches will malfunction or magnets inside cylinders will become demagnetized.
7 Made to order common specifications 5.4-46 -XC11 Dual stroke cylinder/Single rod !8 5.4-52 -XC12 Tandem cylinder !
Do not use an air cylinder as an airhydro cylinder. If it uses turbine oil in place of fluids for cylinder, it may result in oil leakage. 5. Combine the rod end section, so that a rod boot might not be twisted. If a rod boot is installed with being twisted when installing a cylinder, it will cause a rod boot to fail during operation.
46 43 27 48 46 46 Shock absorber at retraction end A Shock absorber at extension end MXF Maximum 35 MXW Shock absorber at retraction end MXJ MXP Other dimensions are the same as the basic style.
The rotation range under the adjustment of an angle at 60 is indicated below.
In such a case, carry out an adsorption test for confirmation. The vacuum pressure when using an ejector is approximately 60 kPa as a guide. The theoretical lifting force of a pad can be found by calculation or from the theoretical lifting force table.
In such a case, carry out an adsorption test for confirmation. The vacuum pressure when using an ejector is approximately 60 kPa as a guide. The theoretical lifting force of a pad can be found by calculation or from the theoretical lifting force table.
In such a case, carry out an adsorption test for confirmation. The vacuum pressure when using an ejector is approximately 60 kPa as a guide. The theoretical lifting force of a pad can be found by calculation or from the theoretical lifting force table.
46 43 27 48 46 46 Stroke 100 to 150 A Shock absorber at extension end Max. 35 Shock absorber at retraction end Dimensions not indicated are the same as basic type.
With an ejector When a few air cylinders are locally used.
Note 1) This cylinder cannot perform an intermediate stop using an air pressure circuit in vertical operation. In this case, an intermediate stop can be performed only by using an external stopper, etc. Note 2) Made-to-order products should be considered, too, depending on an operating environment, etc.
Therefore, if the actuator motor is used in an environment where strong magnetic fields are present, malfunction or failure may occur. Do not expose the actuator motor to magnetic fields with a magnetic flux density of 13 mT or more. When installing an electric actuator and an air cylinder with an auto switch (ex.
The graphs are based on operation using an SMC DC power input type driver with halfstep energization.
(mm) With auto switch B Without auto switch Stroke range (mm) A Bore size (mm) BP C OA Rc NPT G D E F G H I J K L M N O OB P Q RA RB T V Z B A 10 to 50 82 36 15.6 14 63 92 46 1/8 M5 x 0.8 15 20 77 10.5 38 M10 x 1.5 103 7 17 8 60 9 M8 x 1.25 1/4 53 16 4.2 1.6 16.5 19 depth 12 depth 10.5 75, 100 92 46 10 to 50 96.5 43.5 19.6 17.5 80 106.5 53.5 1/8 1/8 21 25 98 12.5 43 M16 x 2.0 132 6 22 10
Install an air dryer, aftercooler, etc. Excessive condensate in a compressed air system may cause valves and other pneumatic equipment to malfunction. Installation of an air dryer, after cooler etc. is recommended. 3. Drain flushing If condensate in the drain bowl is not emptied on a regular basis, the bowl will over flow and allow the condensate to enter the compressed air lines.
error in unit 0. 1 There is an error in unit 1. 2 There is an error in unit 2. 3 There is an error in unit 3. 2 4 There is an error in unit 4. 5 There is an error in unit 5. 6 There is an error in unit 6. 7 There is an error in unit 7. 0 There is an error in unit 8. 1 There is an error in unit 9. 2 Reserved 3 Reserved 3 4 Reserved 5 Reserved 6 Reserved 7 Reserved : The data of diagnostic