60 Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
MY-SA 2 x G F 2 x H E C D A B Side support B MY-SB 2 x J MY1B MY1B MY1H E A B MY1B C D MY1M (mm) MY1C A 61 70 87 B C D E F G H J Part no.
The valve will reach a high temperature when used with high temperature fluids. Use caution, as there is a danger of being burned if a valve is touched directly. 2. When problems are caused by a steam hammer, install a steam hammer relief device such as an accumulator. 3.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
A scraper is not installed. A separate version -X324 (with a felt dust seal) is available in cases in which dust, etc. is dispersed throughout the environment. Mounting taps have been added on the surface opposite the standard positions.
Note 3) A particulate generation test has been conducted in a vacuum environment of 105 Pa. a t e l u g c Stainless steel linear guide & low particulate generation vacuum grease e i 2 t n r a e p r a 0.0 10 0 20 10 w t i o o n L Operation cycles a t e l u g c e i t n 1 r a e Particulate generation from the linear guide unit has been reduced with the use of a stainless steel linear guide and
D-A59W D-Z7/Z80 D-M9/M9W D-M9A Bore size (mm) Bore size (mm) D-Z7/Z80 D-A5/A6 A B A B A B A B A B A B Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs 40 50 63 80 100 40 50 63 80 100 11.5 8.5 8 5 13 10 5 2 27 28.5 27 34 35.5 28.5 29 27 13 8 9.5 4.5 14.5 9.5 6.5 1.5 33 33.5 33 38.5 39.5 34.5 33 33 4.5 0 8.5 3.5 47.5 38.5 14.5 9.5 11 6 16 11 8 3 38.5 38 38.5 43.5 45 38.5 28 37 8.5 3.5 12.5 7.5 54
A total adjustment of approximately 4 to 0 mm is possible using both sides. 4) After completing the stroke adjustment, tighten the inner cover holding screw with a hexagon wrench, etc. D1. In order to maintain the particulate generation grade, use operation of 1 million cycles or travel distance of about 200 km as a guide.
MY-S25 MY-S32 MY-S40 Applicable cylinder A 105 130 145 B 119 148 167 C 35 45 55 D 50 64 80 E 8 11.7 14.8 F 5 6 8.5 G 9.5 11 14 H 5.5 6.6 9 J M6 x 1 M8 x 1.25 M10 x 1.5 A B A B A B MY1H25 MY1H32 MY1H40 MY1 HT Side supports consist of a set of right and left supports.
MA Finger A B C D1 to 1.5 Attachment 1 to 1.5 Finger insertion groove A Lubrication/MHR2, MHR3 Opening/closing direction Max. tightening torque Nm Warning Cross direction Pin insertion hole Model Applicable bolt Attachment -10 -15 -20 -30 -10 -15 This product should be used without lubrication.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or Caution moderate injury. Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death Warning or serious injury. Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or Danger serious injury. Warning 1.
MY-SA 2 x G F E 2 x H A B C D Side support B MY-SB 2 x J A B C D A 61 70 87 B 75 84 105 C D E F G H J Part no.
Apparent power (VA) Volt-ampere is the product of voltage (V) and current (A). Power dissipation (W): For AC , W = V/A cos. For DC, W = V/A. (Note) cos shows power factor. cos = 0.6 2. Surge voltage A high voltage which is momentarily generated in the shut-off unit by shutting off the power. 3.
D 8 I m + mL kgm Find the gripper's moment of inertia. b a+b 12 I = m + mL kgm a Find the actual moment of inertia.
Therefore, make sure to use a pressure regulator to convert line pressure into supply pressure for the actuating valve and the brake valve. In order to actuate multiple cylinders at once, use a pressure regulator that can handle a large air flow volume and also consider installing a surge tank.
-X 21 MXH Series Table Displacement Table Accuracy Table Displacement due to Roll Moment (Reference) Stroke (mm) Traveling parallelism 5 to 30 0.05 mm or less 40 to 60 0.1 mm or less Table displacement (at A) when a load acts upon section F at the full stroke of the Compact Slide A F Mr A Values when no load and no pressure applied.
Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc. The operating ranges shown in the catalog should only be used for stopping pallets on a conveyor. If loads connected directly to a cylinder, etc., are stopped with a stopper cylinder, the cylinder's thrust will become a lateral load. Please consult with SMC in this case. Danger 1.
Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc. The operating ranges shown in the catalog should only be used for stopping pallets on a conveyor. If loads connected directly to a cylinder, etc., are stopped with a stopper cylinder, the cylinder's thrust will become a lateral load. Please consult with SMC in this case. Danger 1.
Extend the dimensions of A, H. when using a single/double knuckle joint together with a rod end nut. (To extend dimensions A/H, refer to the table below, and specify the product as Made-to-order -XAO.) Pin and cotter pin are attached for double knuckle joint.