MHC2 Use this as a standard when mounting, etc. Misc.
If a bend (R) is used, limit it to R3 or less. piping, the piping material and tubing need to be taken into consideration when designing the system.
MGPWM MGPWL/A MGPWM MGPWL/A MGPWM MGPWL/A MGPWM MGPWL/A MGPWM MGPWL/A 1.63 1.74 1.51 1.34 1.08 0.99 1.20 2.10 20 4.36 3.46 2.87 3.93 3.07 2.76 3.45 3.97 2.74 3.28 2.90 2.59 2.14 1.97 2.34 3.53 25 6.78 5.43 4.51 6.27 4.90 4.40 5.51 6.88 6.39 7.00 6.19 5.54 4.59 4.22 5.02 7.98 32 8.48 11.14 9.36 12.46 9.83 8.87 11.00 11.13 7.04 7.72 6.82 6.11 5.06 4.66 5.54 8.80 40 9.34 12.27 10.31 13.73 10.83
A + A' A' w After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved. A A' A' e When air is supplied for the piston extension, the check valve opens and the piston extends with no delay.
Over current is flowing to the load of a switch output. Internal data error. Contact P/A. Internal data error. Internal data error. Internal data error. Shut off the power supply and then reset the switch. Internal data error. Use an adjustment valve, etc. to reduce the flow rate until it is within the flow rate range.
Input and output ports are connected by a needle valve r. Adjustment ensures that exact equalization occurs between the signal and output supply. The above function allows a low volume signal to provide high volume output with pressure ratio remaining (1:1) for signal to output. Construction IN w o e y EXH EXH t q r OUT SUP u i Component Parts Replacement Parts No.
CKZ25 53B781EL R 1) Mount the top cover to the clamp cylinder, then tighten to the specified tightening torque below. The top cover kit includes a top cover and mounting brackets.
Compact / Lightweight 2 Port Solenoid Valve VDW30/40-XF Series For Air/Water Compact / Lightweight resin body (PPS) IP65 RoHS Weight: 120 g (VDW30-XF) n t r e y l d a i 30 mm c r e i r c e s l t e e c c t b t i Power consumption e e o n d l a n .
Consult with P/A in case of 10mm or less stroke. In general, mounting on a small-size actuator may cause hunting. For prevention, a pilot valve with a built-in output restriction is available. The restriction is removable.
A dryer with heavy duty auto-drain (ADH4000-04) is installed instead of the float type auto-drain (AD44). Option symbol R With circuit breaker A circuit breaker is attached to the side of the air dryer.
A Manual override VND Pilot pressure (MPa) Note) Refer to page 624 for how to order pilot solenoid valves. VCC 0.4 0.3 TQ 0.2 0.1 0 1 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Operating pressure (MPa) 619 A VNC Series Construction N.C. i i o o t t r w r w Port 12(P1) Port 10(P2) u u In the case of 32A to 50A y y N.C.
Note 2) Drain piping, or piping for a stop valve, like a ball valve, is required. 850 size comes with a ball valve. substitute with (Symbol: A).
32 to 50 come in valve element assembly A F A F u Pilot solenoid valve SF4--23 (Refer to the table below.)
Load factor: ((Load weight x 9.8)/Theoretical force) x 100% 3-3-31 Series VZ3000 Built-in Speed Controllers Throttle Valve Characteristics (A B R) VZ35 An exhaust throttle valve is built into the solenoid valve itself, enabling a simple speed adjustment of the cylinder.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
1 e w r e Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com u r u t t y y q q Component Parts Description Material No. Option Standard Stainless steel Body C37 q w e r t y u i o !0 !
on condition r C = 0.90 based on condition r 2 2 Based on condition t, A and C Corrected air flow = 350 (0.75 x 1.00) = 467 l/min (ANR) 3 Based on condition t, B and C Corrected air flow = 1200 (0.95 x 0.90) = 1400 l/min (ANR) 3 Based on condition y; IDUS4E is selected as the model to process an air flow larger than 467 l/min (ANR) with a 50Hz power supply, according to data D-1.
equipment such as a voltmeter.