SJ1000/2000/3000 Series However, for any other mounting method or for side facing and down facing, etc., secure the DIN rail with bolts at uniform intervals using the following as a guide: 2 to 5 stations at 2 locations, 6 to 10 stations at 3 locations, 11 to 15 stations at 4 locations, 16 to 20 stations at 5 locations, 21 to 25 stations at 6 locations, 26 to 30 stations at 7 locations and more than 30 stations
Circuit (of Class 2) which is of maximum 30 Vrms (42.4 V peak) or less, with UL1310 Class 2 power supply unit or UL1585 Class 2 transformer. The Pressure Sensor is a UL approved product only if it has a mark on the body. Use the specified voltage. Otherwise failure or malfunction can result. Use the specified measurement flow rate and operating pressure.
Take appropriate measures so that a force of 30 N or more is not applied to the lead wire.
Do not use a cable longer than 30 m. Wire the DC(-) line(blue) as close as possible to the power supply. When analog output is used, install a noise filter (line noise filter, ferrite element, etc.) between the switch-mode power supply and this product. Environment Do not use the product in area that is exposed to corrosive gases, chemicals, sea water, water or steam.
SI Unit Updates from valve output 0 every 30 seconds.
Take appropriate measures so that a force of 30 N or more is not applied to the lead wire. When instructions are given in the Specific Product Precautions, follow these specifications. 1/2 20 to 25 3/4 28 to 30 1 36 to 38 1 1/4 40 to 42 1 1/2 48 to 50 2 48 to 50 3) If the fitting is tightened with excessive torque, a large amount of sealant will seep out.
Additional tightening should be 30 degrees or less. (AN05-M5 shall be tightened to 0.1Nm or less) Additional tightening should be 30 degrees or less (0.1N.m or less) OK!! BC sintered metal Hold the tip of the product (the end without the screw) and screw it tightly. Do not tighten the sintered metal part with pliers or a pipe wrench.
7-2 Sensitivity adjustment 20 7-3 Manual switching 20 8.Maintenance and Check 21 9.Caution on Handling 22-23 10.Troubleshooting 24-26 11.Option 27-29 11-1 Pilot valve with output throttle 27 11-2 Fork lever type joint (Type IP8100) 27-28 11-3 External feet back lever (Type IP8000) 28 11-4 Resin Cable cramp unit ( Type non-explosion protection) 28 11-4 Scale plate unit 29 13.How to order 30
Edition C: Air consumption on page 30 was corrected. The graphs of Exhaust Characteristics on page 36 were replaced.
Allowable kinetic energy E max=0.43 (J) V=Vax1.4=350x1.4=490mm/s W 30 Ev= xV2= x0.492=0.36 (J) 2g 2x9.8 Load factor a5= E = 0.36 =0.84 Emax 0.43 Examination of load factor a5 = 0.84 1 OK With above allowable value, there is no problem on the selection. ML2B25 is selected.
Do not use a cable longer than 30 m. Wire the DC (-) line (blue) as close as possible to the power supply.
Chamfer Chamfer (1) For male thread (2) For female thread 30 30 D-2 D-2 D D Fig. 2 Rod end style Do not apply excessive lateral load or external force to the lock unit. They may break the lock unit. Do not use the product in applications where the rod rotates. Do not apply loads with impact, strong vibration or rotational forces while the lock mechanism is activated.
Bore Arm angle( (mm) 75 90 105 120 15 30 45 60 135 0 0 0 0 0 0 0 0 0 50 15 30 45 60 75 90 105 120 135 -4 -5 -5 -5 -5 -5 -5 -6 -9 0 0 0 0 0 0 0 0 0 63 15 45 30 60 75 90 105 120 135 -3 -4 -5 -5 -5 -5 -5 -6 -9 (7) Do not disassemble the power clamp cylinder. The power clamp cylinder consists of a completely sealed structure in order to protect it from welding spatter.
Contact SMC regarding class 2 turbine oil (with additives), ISO VG32. 1/2 28 to 30 3/4 28 to 30 1 36 to 38 11/4 40 to 42 11/2 48 to 50 2 48 to 50 Air source Connection of piping to products When connecting piping to a product, refer to its instruction manual to avoid mistakes regarding the supply port, etc.
Drain flushing Rc1/2 28 to 30 Rc3/4 28 to 30 If condensation in the drain bowl is not emptied on a regular basis, the bowl will overflow and allow the condensation to enter the compressed air lines. It causes malufunction of pneumatic equipment. If the drain bowl is difficult to check and remove, installation of a drain bowl with an auto drain option is recommended.
Max. voltage (with no load) : 30 Vrms (42.4 V at peak) or less Max. current : (1). 8 A or less (including shorts), and (2).When controlled by circuit protector (fuse, etc.) with the following rating (2) A circuit (Class 2 circuit) with maximum 30 Vrms (42.4V peak) or less, and a power supply consisting of a class 2 power supply unit confirming to UL1310, or a class 2 transformer confirming
HOW TO ORDER AR 30 03 BG B K 1 4 5 6 3 2 1 1 1 1 Symbol Description Body size 20 25 30 40 50 60 Reverse flow function K With reverse flow function 2 2 2 2 Nil Rc N NPT F G Thread type 3 3 3 3 01 1/8 02 1/4 03 3/8 04 1/2 06 3/4 10 1 4 4 4 4 Port size Nil Without mounting option B With bracket H With set nut for panel mounting a Mounting Option Nil Without pressure gauge E Square embedding
Therefore, if the valve is to be energized for periods of longer than 30 minutes at a time or if during the hours of operation the energized period per day is longer than the de-energized period, use the standard type (0.4 W) at ambient temperature of 40C or less with proper heat radiation. 3. Intermediate stops. Rubber seal: Use a closed center type valve.
Symbol Number of arranged elements 4 7 13 19 Number of arranged elements 30 36 55 83 04 07 13 19 30 36 55 83 Symbol Nominal filtration accuracy (m) Note) Nominal filtration accuracy (m) 0.5 1 2 5 10 20 40 Symbol Nominal filtration accuracy (m) 50 70 74 75 100 105 120 X50 001 002 005 010 020 040 050 070 074 075 100 105 120 Symbol Element length Element length L250 L500 (L250 x 2) L750 (L250
Low Friction: Double Acting Single Rod Series CJ2Q 10, 16 How to Order Bore size 10 16 10mm 16mm Mounting Basic Axial foot Front flange Double clevis Standard stroke (mm) B L F D 10 16 15, 30, 45, 60, 75, 100, 125, 150 15, 30, 45, 60, 75, 100, 125, 150, 175, 200 CJ2Q L 16 60 Standard L 16 60 C73 CDJ2Q With auto switch Number of switches With auto switch (Built-in magnet) 2 1 n S n Auto switch