Centering Unit BRAZIL SMC Pneumaticos do Brazil Ltda. CHILE SMC Pneumatics (Chile) S.A. PERU SMC Corporation Peru S.A.C. VENEZUELA SMC Neumatica Venezuela S.A. OCEANIA AUSTRALIA SMC Pneumatics (Australia) Pty. Ltd. NEW ZEALAND SMC Pneumatics (N.Z.) Ltd. EUROPE AUSTRIA SMC Pneumatik GmbH (Austria) BELGIUM SMC Pneumatics N.V./S.A.
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 37
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 38
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not cut the tube with cutting pliers, nippers, scissors, etc.) 2. Grasp the tube, then slowly push it until it comes to a stop. 3. Then, pull it back gently to make sure that it does not come out.
When washing the micromesh element, do not wipe it using a stiff brush or rag. 0.03 12 08 20 24 10 16 Pressure drop (MPa) 06 0.01 0.005 COM. N.O.
When installing and removing an element, do not scratch or damage it by touching the corners of the case, etc.
Do not allow the weight of piping to lie directly on air dryer. 4. Do not connect a tube smaller than the port size to the inlet side. In particular, when using a resin tube, make sure that the size would not be smaller than the port size.
Do nol apply voltage potential In excess of 250V. (Note) Indicator oanel Denatured PPO Swagelok* IS a registered trademark 0 1 Crawford Fitting Co. VCRlI lS a registered trademark. of Cajon Co.
VQC1000/2000 series valves do not come with mounting screws or gaskets. For VQC4000/5000 series valves, when a valve is ordered individually, it comes with a mounting screw but no gasket. VQC1000/2000 series valves do not require separate mounting screws as there are clamp screws built into the manifold.
VQC4000/5000 series valves do not have common polarity.
② For manifolds with serial transmission kits, whether the valves are positive common or negative common depends on the type of protocol. For VQC1000/2000 series valves, install valves with the same common specification as the common specification of your protocol.
Do not restrict the flow rate by plugging or mounting a speed controller to the exhaust port.
In addition, SY7120 series valves do not come with a gasket because they are the equivalent of existing SY7000 series body ported valves.
The SY7000 series body ported valve gasket assembly part number is “SY7000-GS-1.”
Do not tighten or loosen the release bolts excessively. Also, do not tighten them with a pneumatic or electric screwdriver because it may damage internal parts of the product.
For further details, refer to the excerpts from the MWB series “Specific Product Precautions” below.
However, unlike KS and KX series rotary One-touch fittings, they do not rotate with low friction. Do not use the product in a manner in which the connected tube swings or rotates with respect to the fitting.
PF2D series: Pure water and liquids that do not corrode or permeate Teflon (Refer to the list of applicable fluids in the catalog.)
LFE series: Fluids that do not corrode the materials of wetted parts (Refer to the list of applicable fluids in the catalog.)
However, new VX2 (with a white coil) series valves do not have mounting holes on the bottom surface of the body, so brackets cannot be retrofitted.
If the part number is “VX2□□□□XNB,” a bracket can be retrofitted because it has a mounting hole on the bottom surface of the body.
Note) 1/2 port size VX2 series valves do not have an option with brackets as standard.
LCD 3. 4. 5. 14 6. 5 Terminal Setting -13No.EX-OML0010CN-C 15 (I/O ) 24 () 27 () 33 () 47 () -14No.EX-OML0010CN-C 1. I/O Monitor(I/O ) I/O [1.I/O Monitor] 2.& 1. 3. 4. 1. 2.4. 16 2.
Doc.IZ*-OMU0031 / Series IZE11 2 7 8 10 10 11 14 15 18 18 F0 19 F1 OUT1 20 F2 OUT2 22 F3 22 F4 23 F5 24 F6 25 F98 26 F99 27 28 31 32 32 34 -1No.IZ*-OMU0031 1) (ISO/IEC)(JIS) 2) 1) ISO 4414: Pneumatic fluid power -General rules relating to systems ISO 4413: Hydraulic fluid power -General rules relating to systems IEC 60204-1: Safety of machinery -Electrical equipment
XL-OMV0002 VR 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2017 SMC Corporation All Rights Reserved 15 XL-OMV0002