EX260-SDN_eng No.6 No.5 No.8 No.7 No.10 No.9 Red flashing Wrong switch setting, Parameter writing error Green On Bus-off state, Duplicate MAC ID 16 32 4 8 1 2 Red flashing Off Green On I/O Connection is in the Timed-Out state Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Bit: 7 0 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Bit No. 6 4 6 4 2 0 0 0 Solenoid on side A 0 2 4 6 8 16 28 30 Output No.
Do not connect multiple NFC readers / writers to a PC. Connection details using the I/O Configurator for NFC and wireless unit To use a wireless system, it is necessary to "pair" a Wireless Base and Remote. Configure this using the I/O Configurator (NFC version).
Do nol loosen the recessed head screw on the top of the sensitivity adiusting screw because ii is lor prelenting the screw trom slipping otf. @
DO Without air cushion (mm) B Bore size (mm) No.
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. 1. Operate within the range of the maximum operating pressure. Caution 1. After a long period of non-use, perform inspections before beginning operation. 2.
If operating pressure is over the range then cylinder will be damaged and injury by broken pieces. (4) Do not put your hand into the slit of the body without confirming safety. Injury and Bodily harm will occur with the valve operated when valve is operated valve. (5) Do not remove the Cover Fig.1 29 on the actuating part.
Do not apply pressure to this hole. Attach tubing to the vent hole and place the end of the tubing so it is not exposed to dust or water. For the rod end male thread, refer to page 247.
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. 1. Cut the end of the tubing at a right angle and pass it through the fitting nut. After placing the tubing in the holder, push it onto the insert bushing until it stops and clamp it with the knob.
Do not reuse if disassembled. High strength adhesive is applied to the portion of the connection that is threaded to prevent it from loosening, and it must not be disassembled.
Identifying Version Symbols For versions lower than V2.0 and S2.0: Do not use with controller parameters higher than V2.0 or S2.0. Applicable models Applicable models JXC91m Series JXCD1m Series JXCP1m Series JXCE1m Series For versions higher than V2.0 and S2.0: Do not use with controller parameters lower than V2.0 or S2.0.
Customers do not need to apply for a license to use this equipment. Be sure to comply with the following precautions. Do not disassemble or modify the product. Disassembly and modification are prohibited by law.
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. LVA LVH LVD LVQ When the tubing is curved, straighten it out before using it. Maintenance The tubing may slip if there is oil or dust, etc., on the holder.
Do not remove the cushion valve mechanism which prevenlS accidental removal of cushion valve. If removal of the CUShion valve mechanism is required, when thIS work is done the air supply must be turned off to prevenl election 01 the CUshion valve from the cover. i OUT 7.79 195 390 584 779 974 1130 80 25 IN 7.03 176 352 527 703 879 1019 !
Do not immerse the cylinder in water or chemicals. When the cylinder is operated in a condition with water pressure, the fluid leaks into the cylinder in the early stages. In the worst case, the fluid may back flow inside the piping and damage the solenoid valve. Maintenance Warning Mounting 1.
However, do no rotate the cushion valve exceeding two turns, and do not rotate the speed controller valve exceeding four and half turns (40: maximum two turns). If 0.6 Nm or more of torque is applied, the valve may become loose and may jump out depending on the amount of air pressure. Cushion Adjustment The air cushion is built in on the head end for the CK1 series.
Do not disassemble the power clamp No special maintenance is necessary because the power clamp has a fully enclosed design to protect the clamp against welding spatter, and also the power clamp has a contamination resistant construction. Do not disassemble any parts other than replaceable parts, otherwise it may reduce the performance of the clamp cylinder. 3.
Also, do not attempt to tighten the bumper bolt without using a nut. If the dumper bolt is removed, the piston hits the head cover causing damage to the cylinder. Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3.
Conduit terminal: VP3185-T A B DIN terminal: VP3185-D A B [110] 81 35 Light (For TL, TZ) Max.12 31.3 G1/2 Applicable cable 6 to 12 Light position (For DL, DZ) G1/2 NO NO PE PE [243] 237.6 239 228.5 213 31 31 130 130 52 52 41 41 105 105 [ ]: With indicator light (TL, TZ) 1312 Note) CE-compliant: D/DO only (Electrical entry) VP3145/3165/3185 Series Made to Order [Option] Please contact SMC
Do not use compressed air that contains chemicals, organic solvents, salt, or corrosive gases. Do not use compressed gas containing chemicals, organic solvents, salt or corrosive gas. This can cause rust, damage to rubber and resin parts, or malfunction. Liquid surface of drain Discharge drainage until the drainage level reaches the center. 3.