POWER CLAMP CYLINDER Do not disassemble, except for when replacing any of the replaceable parts, as this may cause the performance to deteriorate. (8) Proximity switch output The switch output signal is output near the clamping end and the unclamping end respectively.
Do not apply excessive force or impact. This may damage the product, as well as, decrease its performance and life expectancy. Do not disassemble the parts that are not explained in this operation manual. This may decrease the performance and life expectancy of these parts. In addition, disassembly may cause danger. Torque values specified in this manual must be followed.
The lock might not disengage or might become damaged if a load ratio of 50% is exceeded. t Do not synchronize multiple cylinders. Do not operate two or more end lock cylinders synchronized to move a single workpiece because, one of the cylinder locks may not be able to disengage when required. y Operate the speed controller under meter-out control.
11H9 Depth 1.5 35 Positioning pin hole MHZ2 47.5 9 MHZJ2 58 15 MHQ Auto switch mounting groove position M5 X 0.8 (Finger opening port) MHL2 MHR 3 O 13 MHK S MHS 3 4 23 7 M5 X 0.8 (Finger closing port) 2 MHC2 MHT2 MHY2-10D2 Opening/closing direction through hole type 43.4 MHY2 (Hole for mounting attachment) MHW2 6 0.005 0.025 3 6 MRHQ 12 Auto switch (Limited area for mounting attachment) Do
Do you have a process requiring cost-efficient automation? Do you have a new series of safety features to implement? In fact, do you need another pair of hands in order to solve that troublesome domestic project?
Tidy Un-friendly What do you think to the manual presentation? ! ! ! Yes Not too bad Unusable Are the explanations understandable? Which explanation was most difcult to understand: . . ! ! Are there any diagrams which are not clear? Yes No If so,which:. ! ! ! What do you think to the manual layout?
Do not drop nor apply excessive force. It may cause malfunction or damage. 3. Tighten switch by applying the wrench on the fitting part. Turning it by applying a wrench on the main body may cause damage to the product. 4. Mounting is possible in either horizontal or vertical orientation.
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. 1. Operate within the range of the maximum operating pressure. VC VDW Caution VQ 1. After a long period of non-use, perform inspections before beginning operation. 2.
Do not use in lines where a pressurized condition is maintained, as the body may be damaged. Warning Caution 1. Tubing attachment/detachment for One-touch fittings 1) Installing the tubing (1) Use tubing with no flaws on its periphery and cut it off at a right angle. When cutting the tubing, use a tube cutter, TK-1, 2 or 3. Do not use pinchers, nippers or scissors, etc.
Do nol loosen the recessed head screw on the top of the sensitivity adiusting screw because ii is lor prelenting the screw trom slipping otf. @ World Wide QS\E Support... North American Branch Offices For a branch office near you call: 1-800-SMC-SMC1 (762-7621) SMC Pneumatics lnc. (Milwaukee) SMC Pneumatics lnc. (Richmond) SMC Pneumatics Inc.
Tightening Torque for Stroke Adjustment Unit Holding Bolts Unit: Nm Bore size (mm) 25 32 40 Tightening torque End lock 1.8 3.5 Operating direction 5.8 L R Caution R L R L R L R L Do not operate with the stroke adjustment unit fixed in an intermediate position.
Do not move the cover upward inadvertently during end plate installation.
Do not block the bleed hole. If the bleed hole is blocked, the product will not operate properly. VBA VBAT AP100 875
Please do not apply force to the coil and frame when installing the piping and valves. If they receive 10 N or more of force, a malfunction may occur. 3. Do not pull the lead wire with excessive force. Applying 10 N or more of load may result in broken wire or contact failure. Manual Override Caution 1.
The lock might not disengage or might become damaged if a load ratio of 50% is exceeded. t Do not synchronize multiple cylinders. Do not operate two or more end lock cylinders synchronized to move a single workpiece because, one of the cylinder locks may not be able to disengage when required. y Operate the speed controller under meter-out control.
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. 1. Operate within the range of the maximum operating pressure. VC VDW Caution VQ 1. After a long period of non-use, perform inspections before beginning operation. 2.
Do not hurt the body seat during installation. Compression of the O-ring of the mating side of the body shall be 0.7 to 0.9mm.
If the product is bent to less than the minimum bending radius, the moisture control tube will be Do not use the product in conditions of compressed air or an environment containing solvents. Recommended equipment coupling after inserting the sleeve again before the fitting is installed when if it slips off. not come out.
Troubleshooting Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Manifolds SJ2000/3000, S0700 series : Refer to the catalogues and operation manuals for details on the solenoid valves and manifolds. How to mount the manifold 1.