Escapements Series MIW/MIS ø8, ø12, ø20, ø25, ø32 1 Do not use in an environment where vibration or impact occurs. Please contact SMC about use under such conditions because it can cause fracture or malfunction.
DO Without Air Cushion B Bore size (mm) Part no.
Do not allow hands or fingers near the cylinder during its operation. Your fingers may be caught between the body and the plate. If you need to come near the cylinder during its operation, install a cover on the cylinder. 4. Do not bring objects that are sensitive to magnetism near the cylinder. There is a magnetic built into the cylinder.
DO MY Bore size (mm) 22 22 30 30 45 45 60 CY DX DS DH Z DDH10 DC DT DU DR DO DL DE B DA DB Model 20 25 32 40 50 63 80 14 14 20 20 30 30 32 7 7 8 8 10 10 14 44 44 60 60 86 86 110 15 15 18 18 22 22 24 10 10 11.5 11.5 14 14 15 6.6 6.6 9 9 11 11 13.5 9 9 10.5 10.5 12.5 12.5 13 62 62 81 81 111 111 136 42 42 53 53 73 73 90 32 32 43 43 64 64 78 39 43 49 59 71 82 106 +0.058 0 +0.058 0 129 151 185
When raising the unit, do not insert your hands or fingers. As this is a heavyweight product, be sure to use caution. Screw holes for installing eyebolts are provided for 180, 200 and 250. (Eyebolts are not included in the unit.) Tie-rod nut, Spring washer Cylinder Tie-rod -X Wing nut Unit holding tie-rod 3.
Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2. Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider by hand (or the piston slider with air pressure) back to the proper position at the stroke end.
As an air slide table has magnets built-in, do not allow close contact with magnetic disks, magnetic cards or magnetic tapes. Data may be erased. 4. When mounting an air slide table, use screws with appropriate length and do not exceed the maximum tightening torque. Tightening with a torque above the limit could malfunction.
Piping: Common SUP/Common EXH, Stations: 2 Stations, Bracket: Bracket
Manifold Type: Body Ported, Bar Manifold, Individual Wiring, Valve Stations: 2 Stations, A, B Port: NPTF, Q: Q (CE Marked)
Manifold Type: Body Ported, Valve Stations: 2 Stations, A, B Port: NPTF, CE Marked: Q (CE Marked)
Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Specifications x100 IP address x 10 1 DIP SW Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result.
Specifications Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Technical documentation giving detailed configuration information and the GSD file can be found on the SMC website (URL http://www.smcworld.com). Specifications Do not operate in an atmosphere containing flammable or explosive gases.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Connect valve manifold to the SI unit. Refer to the EX260 series valve manifold section in the valve catalogue for valve manifold dimensions. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the bonnet assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the bonnet assembly itself. Do not disassemble the parts that are not explained in this operation manual.
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the handle assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the handle assembly itself. Do not disassemble the parts that are not explained in this operation manual.
Do not use it for an application in which rotation or oscillation is applied. (2) Use a foot type or flange type bracket to mount a cylinder. If a clevis type or trunnion type bracket is used, the cylinder shaft will not be fixed and it will be able to rotate.
Handling notes 6.1 Cautions for handling of the vertical auto switch unit (1) Be sure to connect a load to the switch before turning the power supply on. (2) Do not let objects drop onto or dent the product or subject it to strong impact when handling. (3) Do not use the product in the presence of a strong magnetic field. (4) When using two or more cylinders with auto switches closely in
Precautions Do not turn off the controller for communication while the setting software (ACT Controller) is running. Do not connect or disconnect the cable while the setting software is running. The communication is continuously established while the setting software is running.