Title not found I EASY TO ATTACH SMALL DIAPHRAGM ACTUATORS The pneumatic and electrical ports are on the side of the body and do not interfere with the feedback lever on the other side. I STABLE OPERATION Control is very stable even on small sized actuators.
Panel mount Apply atmospheric pressure then do 0 clear. ZSP ISl ZSM 1 Turn screw 1/4 to 1/2 turn after panel makes contact with the sealing surface of the PSE. PFl IFl Removal from DIN rail Mounting on DIN rail 2a 2b Others Caution 1. Time delay for power on reset of controller is 0.5 seconds.
Do not pull on the cord.Have the case when remove the ECC-PNAL-232CAB cable. This cable might break when the code part of this cable is pulled when this cable is removed. Install the cover or the memory cassette after removing the ECC-PNAL-232CAB cable. Turn off the power supply when you install or detach the ECC-PNAL-232CAB cable.
Do not use in locations where there is splashing or spraying of oils and solvents. OUT2 OUT1 3. When using a commercially available switching regulator, be sure to ground the FG terminal. SET 4. In locations where the switch is exposed to water and dust, etc., these may enter the switch from the atmospheric release port.
Do not set the mist generating pressure differential to exceed 0.2 MPa. Warning PPA 1. Before removing the oil filler plug, loosen it two and half turns to completely release the pressure in the bowl. This will prevent the oil filler plug from flying out.
Do not use a lubricator on the inlet side because it could clog the bleed holes and lead to a malfunction. 14-4-60 1 Regulator for 2 MPa Series ARX20 F.R.L.
Do NOT pipe upwards. AU200/300 Effective thread depth 6.5 4-M5 x 0.8 AU200, 300 Float type auto-drain Port size H G F E D C B A Model Port size 1 4 / 3 8 AU200 / 50 70 61 30 40.5 31.5 164 165 AU300 50 70 61 30 40.5 31.5 188.5 165 14-3-12
Do not use in an environment, where water or oil is splashed. Because it is the open type construction. If water or oil were to make an ingress, the electrical circuit would be corroded and result in a malfunction or damage. 2. Operating fluids are either air or inert gas exclusively. Never use liquids. 3. Never use in an environment where flammable fluid or gas is used.
Therefore, do not operate it in an environment that is exposed to chemicals such as thinner, carbon tetrachloride, chloroform, acetic ester, aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid, or water-soluble cutting oil (alkalinic). 2.
Do not use in locations where there is splashing or spraying of oils and solvents. 3. When using a commercially available switching regulator, be sure to ground the FG terminal. OUT2 OUT1 SET 4. In locations where the switch is exposed to water and dust, etc., these may enter the switch from the atmospheric release port.
When this is done, take care that the coverings of the lead wires do not enter the core wire crimping area. (Crimping tool: model no. DXT170-75-1) Set point ON When assembling the connector to the switch housing, push the connector straight onto the pins until the lever locks into the housing slot.
BRAZIL SMC Pneumaticos Do Brazil Ltda. CHILE SMC Pneumatics (Chile) S.A. VENEZUELA SMC Neumatica Venezuela S.A. ASIA CHINA SMC (China) Co., Ltd. HONG KONG SMC Pneumatics (Hong Kong) Ltd. INDIA SMC Pneumatics (India) Pvt. Ltd. MALAYSIA SMC Malaysia (S.E.A.) Sdn. Bhd. PHILIPPINES SMC Pneumatics (Philippines), Inc. SINGAPORE SMC Pneumatics (S.E.A.) Pte. Ltd.
style cannot be mounted on the same manifold. 02 2 stations 1 2 3 Stations Uside Dside 3m 18 18 stations VVQ100-10A-1 Electrical entry Multi-connector C Connector location U S Top entry Side entry Cable length 0 1 2 3 Without cable With cable (1.5m) With cable (3m) With cable (5m) Option None DIN rail mounted (With standard length of DIN rail) DIN rail mounted (Without DIN rail) D DO
Note) Do not use excessive force to remove the connector as this might loosen the wire connections inside the connector. Open the cover by inserting a small flat head screw driver into the slot on the side of the pilot assembly(see drawing below), lift the cover out about 1 mm and then pull off.
SYJ W Non-locking push style (Flush) SX VK Note: To avoid contact failure and broken wires, do not pull out the lead wire with excessive force.
Do not use a pair of pliers, nippers, or scissors because they could result in an uneven cut or cause the tube to become flattened. As a result, it might not be possible to connect the tubing, or after the tube has been connected, it could pull out or allow air to leak.
Parenlneses CPA1 BN do Boot with Boot' BORE D E G'GB J K M MM N P H z.
(Do not cut the tube with plier6, nippers, scissors, utilitv knife, etc.) ePull out the tube while keeping the release button depressed. lJf the release butlon is nol held down, the tube cannot be withdrawn.) OGrasp the tube, then slowly push it until il comes lo a dead-end.
BRAZIL SMC Pneumaticos Do Brazil Ltda. CHILE SMC Pneumatics (Chile) S.A. VENEZUELA SMC Neumatica Venezuela S.A. ASIA CHINA SMC (China) Co., Ltd. HONG KONG SMC Pneumatics (Hong Kong) Ltd. INDIA SMC Pneumatics (India) Pvt. Ltd. MALAYSIA SMC Malaysia (S.E.A.) Sdn. Bhd. PHILIPPINES SMC Pneumatics (Philippines), Inc. SINGAPORE SMC Pneumatics (S.E.A.) Pte. Ltd.
(Do not use machine oil or spindle oil ) When bottom mounting, the guide shaft will protrude from the bottom surface Therefore' drill a hole lor a hexagon-holed bolt for mounting and an escape hole for guide shaft on the mounting surface.