Modular Type Lubricators Series AL Clearance For Maintenance W E G A AC-B AA M J N F (2) P1 (Port Size) C B Q Q V IN OUT K P2 (Gauge Port Size) Bracket and Relief Valve (Optional) U Min.
Port size Enclosure C4 C6 C8 C0 F0 F1 F2 F3 P1 P2 P3 L0 L1 L2 T1 T3 M1 M2 M3 Nil W Dust-protected Dust-tight, Water-jet-proof (IP65) With 4 One-touch fitting With 6 One-touch fitting With 8 One-touch fitting Without One-touch fitting (With clip) Without lead wire F kit for 2 to 12 stations/Double wiring F kit for 13 to 24 stations/Double wiring F kit for 2 to 24 stations/Single wiring P/J
The air pressure forms a bridge circuit inside the unit with a vacuum applied to the circuit, but with the adsorption nozzle S4 open, adjust needle S2 so that (P1 P2). When parts are absorbed by nozzle S4, the resulting (P2 P1) differential will be detected by the pressure sensor.
CYLINDER, P2, 63MM CKZN SLIM LINE CLAMP CYL, 3.63660 lb
CYLINDER, P2, 63MM CKZN SLIM LINE CLAMP CYL, 4.05900 lb
SLIM LINE CLAMP CYLINDER, P2, 63MM CKZN SLIM LINE CLAMP CYL, .64480 lb
Set each P1/P2 (set value), referring to the Setting method on page 26. (When reversed output is selected, the sub display (left) shows [n1/n2].)
IBV1 Series SMC Corporation 1.Index 1Table of contents P1 2Specifications P2 3Features P2 4External dimensions drawing P3 5How to mount a nozzle P4 6Relationship between Upstream Piping and Peak Pressure P5 7Safety Instructions P6~10 1 2.
P1 = Pw + Pu > Pw To reduce the internal pressure of the tank, reduce the pressure with the discharge valve(E) of the tank before resetting with REG(1). 3) Cylinder upper chamber pressure(P2) which is set by VEX A YE A and REG(2) is the pressure which overcomes compressed pressure(Pu + P) in the lower chamber to the tank chamber at the lower end of the stroke.
area at exhaust side (mm2) AEA 40 1.25-3.5M, 1.25Y-3L, 1.25-3M 36 S at P2=0.5 MPa BEB Although A-, COM+ and Bmarks are indicated on the Note 1) Maximum operating pressure of solenoid valve is 0.9 MPa. terminal block, VFR3000 can be used as either +COM or Note 2) Set the pressure within operating pressure range of -COM. solenoid valve.
AW30K-D: Max3.5 AW40K-D : Max5 Center of piping Center of piping Center of piping (Port size) (Pressure gauge port size) maintenance Clearance for Dimensions Optional specifications Round type Digital Round type Model Standard specifications Square Round type pressure gauge pressure pressure embedded type pressure gauge pressure gauge (Semi-standard: (With color zone) switch gauge Z) P1 P2
mm2) S at P2=0.5 MPa BEB 11 Change Direction of DIN Connector/Cable Entry Unscrew retaining screw, pull off outer cover, rotate connector block through 180.
Flow rate l/min (ANR) Flow rate l/min (ANR) Flow rate l/min (ANR) 400 Effective area mm2 Effective area mm2 Effective area mm2 6 12 1000 15 300 8 4 500 10 200 500 4 2 5 100 10 5 0 10 5 0 10 5 0 Number of needle rotations Number of needle rotations Number of needle rotations Pressure Characteristics (ASR) ASR430F, ASR530F ASR630F 0.4 0.4 Set pressure 0.3 MPa Set pressure 0.3 MPa 0.3 0.3 P2
Flow rate l/min (ANR) Flow rate l/min (ANR) Flow rate l/min (ANR) 400 Effective area mm2 Effective area mm2 Effective area mm2 6 12 1000 15 300 8 4 500 10 200 500 4 2 5 100 10 5 0 10 5 0 10 5 0 Number of needle rotations Number of needle rotations Number of needle rotations Pressure Characteristics (ASR) ASR430F, ASR530F ASR630F 0.4 0.4 Set pressure 0.3 MPa Set pressure 0.3 MPa 0.3 0.3 P2
(mm) H A (1) Weight (g) Thread R(PT) D1 D2 P2 L2 L3 M P1 L1 Part No.
S1 S2 Preset pressure OFF OFF P1 ON OFF P2 OFF ON P3 ON ON P4 For safety reasons, it is recommended that one of the preset pressures be set to 0MPa. 1.12-16
= 0.5 MPa Effective area at supply side (mm2) S at P1 = 0.7 MPa, P2 = 0.5 MPa Note 3) 5.1 1.9 PA 5.8 2.1 PB Note 3) 12.6 4.5 AEA 12.6 4.5 BEB 1-5-80
= 0.5 MPa 31 Effective area at exhaust side (mm 2) S at P2 = 0.5 MPa Note 1) Maximum operating pressure of solenoid valve is 0.9 MPa.
Note 4) Interface regulator is only capable of regulating the P port pressure. 0.06 1.9 2.1 4.5 4.5 P A P B A EA B EB Effective area at supply side (mm2) (3) S at P1 = 0.7 MPa, P2 = 0.5 MPa Effective area at exhaust side (mm2) (3) S at P2 = 0.5 MPa How to Order Solenoid Assembly Non plug-in type C DXT170 5 L Flow Characteristics {1(P) 4(A)} Conditions: Inlet pressure setting 0.7 MPa
(inch) Connection thread UNF NPT H (Width across flats) Min. port size D1 Note) D2 L1 P2 A Weight (g) Model L2 M P1 L3 1 8 1 8 5 32 3 16 KQ2ZD01-34S KQ2ZD03-34S KQ2ZD05-34S KQ2ZD07-34S KQ2ZD07-35S KQ2ZD07-36S KQ2ZD09-35S KQ2ZD09-36S KQ2ZD09-37S KQ2ZD11-35S KQ2ZD11-36S KQ2ZD11-37S KQ2ZD13-36S KQ2ZD13-37S 14.29 14.29 14.29 9.6 10.4 11.4 37 37 37 37.5 38.5 40.5 45 45.5 47.5 52 52.5 54 60.5