Magnetically Coupled Rodless Cylinder Low Profile Guide Type Series CY1F ø10, ø15, ø25 1 Static moment M2 = m x g x L1 = 0.5 x 9.8 x 0.05 = 0.245 [Nm] 2 = M2/M2 max = 0.245/3 = 0.082 Investigate M2. M1 and M3 are not required because they are not generated.
M2max (from 3 of graph MY1MW: M2) = 24 (Nm) m1 M3 = m1 x g x Y = 6.525 x 9.8 x 29.6 x 10 3 = 1.89 (Nm) Load factor 3 = M2/M2max = 1.89/24 = 0.08 M2 MX 5.
Static moment M2 = m x g x L1 = 0.5 x 9.8 x 0.05 = 0.245 [Nm] 2 = M2/M2 max = 0.245/3 = 0.082 Investigate M2. M1 and M3 are not required because they are not generated.
: Rolling Static Moment Ceiling mounting Horizontal mounting Wall mounting M1 M2 M3 M1 M2 y M2 X x Y z y m1 x g X Z Y m3 x g x X x m2 x g Vertical mounting Mounting orientation Horizontal mounting Ceiling mounting Wall mounting Vertical mounting m1 m2 m3 m4 Note) M3 Static load (m) M1 M1 m1 x g x X m2 x g x X m4 x g x Z Static moment z y Y M2 m1 x g x Y m2 x g x Y m3 x g x Z Z M3 m3 x g
Static moment M2 = WL1 = 100.2 = 2 [Nm] 2 = M2/M2 max = 2/16 = 0.125 W = 1 [kg] = 10 [N] W Review M2. Since M1 & M3 are not generated, review is unnecessary. M L1 3. Dynamic moment We = 5 x 10-3WgU = 5 x 10-319.8300 = 15 [N ] Me3 = 1/3We(L2-A) = 1/3150.182 = 0.91 [Nm] 3 = Me3/Me3max = 0.91/10 = 0.091 Me3 Guide central axis We W L2 Review Me3.
Red LED is flashing EtherNet/IP connection time out Red LED is ON IP duplicated OFF BUS IN side (P1): No Link, No Activity L/A1 Link/Act Green LED is ON BUS IN side (P1): Link, No Activity Green LED is flashing BUS IN side (P1): Link, Activity OFF BUS OUT side (P2): No Link, Activity L/A2 Link/Act Green LED is ON BUS OUT side (P2): Link, No Activity Green LED is flashing BUS OUT side (P2)
VVFS2000-22A-1 VVFS2000-22A-2 Cylinder pressure Check valve G E T D Applicable valve model VFS2400-F VFS2410R1 Solenoid one side energized 210 or less P R2 Piston SUP side pressure (P1) Leakage (cm2/min) R1 210 or less P Solenoid both sides de-energized SUP side pressure P1 (MPa) R2 0 A R1 Operating range B R2 Supply pressure: 0.5 MPa Double check spacer Caution In the case of 3 position
For saturated steam Viewing the graph [664] (183) Upstream pressure of valve P1 = 1.0MPa 1.0 The sonic range pressure to generate a flow rate of 25kg/h for orifice 3 (VCS21) is P1 approx. 0.68MPa for orifice 4 (VCS21) is P1 approx. 0.40MPa for orifice 5 (VCS21) is P1 approx. 0.29MPa The holding heat differs somewhat depending on the pressure P1, but at 25kg/h it is approximately 16000kcal
Applying the same pressure to P1 and P2 is recommended when restarting.
Piston SUP side pressure (P1) SUP side pressure P1 (MPa) Double check spacer Operating range Plug-in type Cylinder side pressure P2 (MPa) Non plug-in type 1184 Series VFS4000 5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in Construction 2 position single 2 position double SJ SY SV SYJ SZ VP4 S0700 3 position closed center/exhaust center/pressure center VQ Closed center
.+100 Name Range of values Setpoint P2 21999 P1+H299.9 P1+H299.9 750 Set the value for energy saving function and vacuum/release confirmation. The value of P2, P1 represents negative pressure, the value of P3 represents positive pressure. Enter a value that is 10 times the pressure value [kPa]. ex) P2 = -65 [kPa] -> P2 sets 650 Refer to Section 4.1.7.
For saturated steam Viewing the graph [664] (183) Upstream pressure of valve P1 = 1.0MPa 1.0 The sonic range pressure to generate a flow rate of 25kg/h for orifice 3 (VCS21) is P1 approx. 0.68MPa for orifice 4 (VCS21) is P1 approx. 0.40MPa for orifice 5 (VCS21) is P1 approx. 0.29MPa The holding heat differs somewhat depending on the pressure P1, but at 25kg/h it is approximately 16000kcal
(A conversion cable is not required for the JXC-W2.) 2 Step Motor Controller JXCE1/91/P1/D1/L1 Series How to Order Actuator + Controller R1 CD17T LEFS16B-100 Controller Nil Without controller Cm1mm With controller Actuator type Refer to How to Order in the actuator catalog. For compatible actuators, refer to the table below.
Static moment M2 = WL1 = 10 x 0.2 = 2 [Nm] 2 = M2/M2max = 2/16 = 0.125 W = 1 [kg] = 10 [N] W C J G5-S Examine M2. Since M1 & M3 are not generated, investigation is unnecessary. M CV MVGQ L1 CC We = 5 x 103 WgU = 5 x 103 x 1 x 9.8 x 300 = 15 [N] Me3 = 1/3We (L2A) = 1/3 x 15 x 0.182 = 0.91 [Nm] 3 = Me3/Me3max = 0.91/10 = 0.091 3.
Static moment M2 = WL1 = 10 0.2 = 2 [Nm] 2 = M2/M2max = 2/16 = 0.125 W = 1 [kg] = 10 [N] W REA Examine M2. Since M1 & M3 are not generated, investigation is unnecessary. REB M REC L1 CY 3. Dynamic moment We = 5 x 103 WgU = 5 x 103 1 9.8 500 = 25 [N] Me3 = 1/3We (L2 A) = 1/3 25 0.182 = 1.52 [Nm] 3 = Me3/Me3max = 1.52/6 = 0.25 CX Me3 Examine Me3.
moment M2 = WL (mm) Model REAH10 REAH15 REAH20 REAH25 REAHT25 REAHT32 A 15 17.5 19.5 23.5 L L A L M2 0 M1 0 M3 Since there are 2 guides, the guides central axis and the cylinders central axis are the same.
hexagon socket head cap screws with 3.3 top diameter, or JISB1101 type M2 round head screws.
Calculation of Load Factor for Static Load m3: Mass m3 max (from q of graph MY1H/m3) = 50 (kg) Load factor 1 = m3/m3 max = 6.525/50 = 0.13 m3 Z M2: Moment M2 max (from w of graph MY1H/M2) = 50 (Nm) M2 = m3 x g x Z = 6.525 x 9.8 x 37.4 x 103 = 2.39 (Nm) m3 Load factor 2 = M2/M2 max = 2.39/50 = 0.05 M2 1206 Model Selection MY1H Series X M3: Moment M3 max (from e of graph MY1H/M3) = 38.7 (Nm
x 36) ARBY3000 SX3000-57-4 Caution M3 x 48.5 (Flat nickel plated) Mounting screw tightening torques ARBY5000 SX5000-57-5 M2: 0.15Nm M3: 0.6Nm ARBY7000 New!
hexagon socket head cap screws with 3.3 top diameter, or JISB1101 type M2 round head screws.