LEF-OM002xx

. / See Operating procedure input / output signals Alarm for Step data ALM2/code: short an interval between the 1-051 is generated. input signal of IN* and the for each operation type on P .27 Drive or inputting the signals at the same time.

LEF-OM006xx

/code1-051 15ms IN* 30ms DRIVE /P25 1) No. RESET 15ms 3 30ms /P25 1) No. No. 4 PLC No. 15ms 1IN* 30ms DRIVE /P25 1) / No. OUT 15ms 2 30msmsec /P25 1) No. OUT -42- No. No. PLC /P25 1) No. OUT 3 INP INP LEFS 0.5 LEFB 1 4 1INP BUSYOFF 5 6 7 () 1 / EMG SVREOFF 2 /CN1 BK RLS DC24V(+) /P34 5.6 8 1 , , EMG SYREOFF /P911 2.1.

DOC1023126

E 60 - Please contact SMC when this alarm is generated. (049) (051) (103) (109) (153) (193) (197) (198) (202) Please contact SMC when this alarm is generated. Warning Thoroughly check safety before resetting the alarm since the operation described below will be performed according to the mode immediately after the alarm is reset by RESET.

Electric Actuator / Guide type 《 Battery-less absolute (Step motor 24VDC) 》

/code: 1-051 is generated.

LEY-OM007

DRIVE /P.30 1 /code1-051 No. 3 RESET 15ms30ms /P.30 1 No. 4 No. PLC No. 15ms 1 IN* 30ms DRIVE /P.30 1 / No. OUT 2 15ms30msmsec /P.30 1 No. OUT 3 No. PLC /P.30 1 No. OUT -52- No.

Electric Slide Table / High Precision Type 《 Battery-less absolute 》

/code: 1-051 is generated.

LEH_C

/code1-051 RESET DRIVE 30ms) /P.34 1) No. 3) 15ms( 30ms) No. /P.34 1) No. 4) PLC No. 1)IN* 15ms( DRIVE 30ms) / /P.34 1) () No. OUT 2) 15ms( 30ms) No. /P.34 1) OUT 3) PLC No. No.

High performance type Step Motor Controller (Servo/24 VDC)

(When operation is commanded through PLC, this alarm will be generated depending on the input signal interval and the holding time of signals) The step data is not registered. (01-051) Operation data error B RESET (1) Make sure that the "Movement MOD" of the step data is not "Blank (Disabled)" input (2) Process delay of PLC or scanning delay of the controller may occur.

JXCx-OMY0008

(When operation is commanded through PLC, this alarm will be generated depending on the signal interval and the holding time of signals) Set step data is not registered on list. (01-051) < Countermeasure > (1) Make sure that the Movement MOD in the step data is not "Blank Step data ALM2 B RESET (Disabled)" and that numbers [1(ABS)] and [2(INC)] or input in the numerical instruction operation

JXCx-OMY0006

(When operation is commanded through PLC, this alarm will be generated depending on the signal interval and the holding time of signals) < Countermeasure > (1) Make sure that the Movement MOD in the step data is not "Blank Set step data is not registered on list. (01-051) Step data ALM2 B RESET (Disabled)" and that numbers [1(ABS)] and [2(INC)] or input in the numerical instruction operation

JXCx-OMY0004

(When operation is commanded through PLC, this alarm will be generated depending on the signal interval and the holding time of signals) Set step data is not registered on list. (01-051) < Countermeasure > (1) Make sure that the Movement MOD in the step data is not "Blank Step data ALM2 B RESET (Disabled)" and that numbers [1(ABS)] and [2(INC)] or input in the numerical instruction operation

JXCx-OMU0026

(When operation is commanded through a PLC, this alarm will be generated depending on the output signal interval and the holding time of the signals) (1) Make sure that the Movement mode of the step data is not Set step data is not registered on list. (051) B RESET Is ON "Blank (disabled)". (2) Both PLC processing delay and controller scan delay are generated.

Step Motor Driver （ Pulse input type ）

RESET Step data ALM2 1-051 B SVON (1) Check if "Operation" of the step data is "Blank (Invalid data)". (2) This product cannot perform test operation by the teaching box or input Controller setting kit.

IDX-OM-W037

Operation/ Shutdown 3.10.6 PID manual setting CH1 PID (control parameter) P Proportion band (050) i Integral time (051) d Derivative time (052) PID(proportion band / integral time / derivative time) is manually set. [ Setting range] P: 0.1 to 999.9 I: 0 to 3200 sec. D: 0.0 to 999.9 sec. PID values are automatically set by auto tuning.

Step Motor Controller (Servo/24 VDC) Incremental / Battery-Less Absolute Encoder compatible

(When operation is commanded through PLC, this alarm will be generated depending on the input signal interval and the holding time of signals) The step data is not registered. (01-051) Operation data error B RESET (1) Make sure that the "Movement MOD" of the step data is input not "Blank (Disabled)". (2) Process delay of PLC or scanning delay of the controller may occur.

Electric Actuator / Slider type 《 Battery-less absolute encoder type (Step motor 24VDC) 》

. / During operation (Not always, but may happen 2) Different input signal to the Add an interval of 15ms (the occasionally) expected step number is inputted recommendation is 30ms) or more between the input signals. to the controller, because of a too short an interval between the /Refer to the JXC controller Alarm for Step data ALM2/code: operation manual. 1-051 is generated. input signal

Electric Actuator / Guide rod Slider

. / See Operating procedure input / output (Not always, but may happen occasionally) Alarm for Step data ALM2/code: 1-051 is generated. signals for each operation type on page 21 3) Different input signal to the expected step number is inputted to the controller, because the input signal time was too short.

Electric Actuator Miniature Rod Type Miniature Slide table Type

. / See Operating procedure input occasionally) Alarm for Step data ALM2 and output signals for each operation type on P.28 /code: 1-051 is generated.

Electric Actuator / Low profile slider type

. / See Operating procedure input / output signals for each operation type on page 25 Alarm for Step data ALM2/code: 1-051 is generated. Input the reset signal. 3) Different input signal to the expected step number is inputted to the controller, because the input signal time was too short.

Port Connections: Straight ports for 1/16" I.D. flexible tubing Barbs for 1/16" or 1/8" I.D. flexible tubing , Straight ports for 1/16" I.D. flexible tubing, Barbs for 1/16" or 1/8" I.D. flexible tubing Size Part Number Color .004 F-2815-041 Purple .005 F-2815-050 Lime .006 F-2815-051