Do not change the setting. (Default value is 1) ACC/ DEC pattern Fixed value This is a fixed value for the controller. Do not change the setting. (The default value varies depending on the electric actuator) S-motion rate Fixed value This is a fixed value for the controller. Do not change the setting.
Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. The product is not designed to be explosion proof. Do not Do not use the product in a place where static electricity is a problem. Otherwise failure or malfunction of the system can result.
20 47.5 63 80 60.5 20 Rc 3/8 22 22 Rc 3/8 22 22 20 60.5 80 100 71 20 Rc 1/2 22 22 Rc 1/2 22 22 20 71 100 For dimensions other than listed above, refer to the dimensions with rubber bumper
11 2-M6 thread depth 11 15 15 35 18 15 2-M6 thread depth 11 2-M6 thread depth 11 20 20 A 17 17 40 A 20 20 15 45 60 25 45 60 A Applicable clamp cylinder A Applicable clamp cylinder Part no.
20 50 98 70 84 44.5 11 6.4 117.5 16 3.3 316 280 46 20 196 11 20 98 50 70 44.5 84 13 319 11 6.4 117.5 3.3 Note 1) For AC20 only, the position of the pressure gauge is above the center of the piping.
Through holes Double end taps Extension locking Easy manual unlocking B Locked A 40 to 100 20 to 32 W Retraction locking Unlocked 40 to 100 20 to 32 W A B Wide variations from 20 to 100 Standard stroke (mm) Locking direction Bore size (mm) Mounting Series 5 10 15 20 25 30 35 40 45 50 75 100 20 Through holes, double end taps common 25 Extension locking 32 40 CLQ Through holes 50 Retraction
Do not bung up with wall and so on. IDU3E to 6E-20/23 (200V/230V AC specification) Rear Panel You can see the terminal block when you remove this cover. Connect the power cable through the membrane grommet.
30 40 50 Stroke[mm] Origin 50mm Motor side End side 10 20 30 40 50 60 Stroke[mm] Origin 50mm Motor side End side -50 -40 -30 -20 -10 0 Stroke[mm] Origin 50mm Motor side End side -40 -30 -20 -10 0 10 Stroke[mm] Origin 50mm Motor side End side -60 -50 -40 -30 -20 -10 Stroke[mm] -29- 4.
mA, 7: 4..20 mA 0..2 (Ch0 in) Analogue input or output range 3 Reserved 3 3: 0..10 V, 4: 0..5 V, 5: 1..5 V, 6: 0..20 mA, 7: 4..20 mA 4..6 (Ch1 in) Analogue input or output range 7 Reserved 0 to 3: 0..10 V, 4: 0..5 V, 5: 1..5 V, 6: 0..20 mA, 7: 4..20 mA 0..2 (Ch0 out) Analogue input or output range 3 Reserved 4 0 to 3: 0..10 V, 4: 0..5 V, 5: 1..5 V, 6: 0..20 mA, 7: 4..20 mA 4..6 (Ch1 out)
TQ1230001-OM103-A grip success: default output DO[101] grip failure: default output DO[102] workpiece drop detection: default output DO[103] * Digital output port can be selected within DO[101] DO[112] * If you select the same digital output port for different status signals, a warning message will be displayed. 3.2.
-A 13.5 Maintenance Warning (1) Do not disassemble or repair the product.
B Z + Stroke DB DX DD 90 B 4DT A DS DH 4DR DB DU DO DO DC DE DU DL Rotation (mm) No.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
5/16-24 A 0.75 0.75 1.25 AA 1.00 1.25 1.75 B 0.625 0.750 1.00 CA 0.093 0.093 0.125 D 0.22 0.25 0.38 DD 10-32 UNF 10-32 UNF 1/4-20 UNC E 0.81 1.12 1.56 EA 1.00 1.25 1.75 EE 1/8 1/8 1/4 NA 1.12 1.47 1.93 NE 0.12 0.24 0.25 NH 10-32 UNF 10-32 UNF 1/4-20 UNC NT 1/4-20 1/4-20 5/16-18 TN 0.62 0.81 1.12 WF 0.34 0.47 0.38 YE 0.88 1.22 1.57 XA 0.38 0.62 0.88 Bore size (inch) 075 (3/4") 106 (1-1/16
Do not use a cable longer than 20 m. Wire the DC (-) line (blue) as close as possible to the power supply. When analogue output is used, install a noise filter (line noise filter, ferrite element, etc.) between the switch-mode power supply and this product. -8No.PF-OMY0002 Environment Do not use the product in an environment that is constantly exposed to the splash of water.
LECSA LEFS25 LEFS32 LEFS40 Series Lead symbol H A B H A B H A B Lead 20 12 6 24 16 8 30 20 10 Parameter Para No Initial value Recommended value Number of command input pulses per revolution *3 PA05 100 100 Electronic gear numerator *3 PA06 1 100(Positioning mode: 10) Electronic gear denominator *3 PA07 1 20 12 6 24 16 8 30 20 10 Feel length multiplication (STM) (Multiplier) PE02 0 0(Less
Note) D1: Max. diameter M5 x 0.8 10.4 8 14 8 14 17 9.8 13.4 9.8 13.4 17.6 20.5 22 23.5 24.5 25 11 15.5 12.5 15.5 20 17 20 25.5 22 24.5 24.5 25.5 20 29.5 20 29.5 38.5 31 38.5 45.5 41 45.5 45.5 50 16 16 4 1 8 M5 x 0.8 25.5 16 25.5 32.5 27 32.5 39 35 39 39 42 D1 1 8 1 4 1 8 1 4 3 8 1 4 3 8 3 8 1 2 6 12.8 17 L3 L2 17.6 28.5 M5 x 0.8 17 15.2 8 18.5 D2 25.2 20.6 25.2 25.2 29.5 22
(mm) 02 04 06 08 10 13 16 20 25 32 40 50 2 4 6 8 10 13 16 20 25 32 40 50 Pad type 02 04 06 08 10 13 16 20 25 32 40 50 2 4 6 8 10 13 16 20 25 32 40 50 Pressure gauge position Thread dia.
Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. The product is not designed to be explosion proof. Do not Do not use the product in a place where static electricity is a problem. Otherwise failure or malfunction of the system can result.
7 t CY3R15, 20 CY3R15 Parts list No. Description No.