CA2 Note 4) When using the D-M9lA(V) or Y7BA, do not use the steel set screws which are included with the above auto switch mounting brackets (BA7-lll, BA4lll). Order a stainless steel screw kit (BBA1) separately, and use the M4 x 6 L stainless steel set screws included in the BBA1. Note 5) There is a difference in the cylinder tube thickness depending on the cylinder model.
(To set the pressure, do so in the direction of pressure increase.) Pressure gauge and One-touch fittings 1. Both the pressure gauge and the One-touch fittings are a cassette type, so that it is possible to rotate them freely. Rotate them after confirming that there is no pressure inside and exhausting air completely. 714
Insert the cover nail into hole of case (\l mark), set the mark( DO ) of the cover to the case and rotate the cover ctockwise until it stops.
To prevent malfunctions, do not clog the breathing port. (When mounted on a metal surface, breathing air can go through from the breathing port to the breathing groove; however, when the valve is mounted on a rubber surface, the breathing air may be blocked by the deformation of rubber.) 2.
Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). The grommet portion contains a breather hole for the core.
VQC SQ VQ0 VQ4 Note) Do not pull on the lead wires with excessive force. This can cause faulty and/or broken contacts.
Do not hold the part of sintered metal with a wrench, etc. to tighten. When the main body is made of metal (Except BC element) [Series 25] Within the recommended tightening torque shown in the chart below, use a wrench on the hexagonal flats and tighten. Tightening by using a pipe wrench or pliers may cause damage to the silencer. This method is not recommended. Caution 2.
clevis type Double clevis type Center trunnion type Front trunnion type 40 50 63 80 100 40mm 50mm 63mm 80mm 100mm Nil J K Nil N R H Without rod boot Nylon tarpaulin Neoprene cloth Both sides Without cushion With front cushion With rear cushion Aluminum tube Rod boot Part nos. for cylinders with built-in magnets Cushion In the case of cylinders with built-in magnets but no auto switches, do
(Do not use machine oil or spindle oil ) When bottom mounting, the guide shaft will protrude from the bottom surface Therefore' drill a hole lor a hexagon-holed bolt for mounting and an escape hole for guide shaft on the mounting surface.
Mounting types Cylinder option Bore size B L F T U Basic type Axial foot type Front flange type Center trunnion type Front trunnion type Nil N R H Both sides Without cushion With front cushion With rear cushion 40 50 63 80 100 40mm 50mm 63mm 80mm 100mm Aluminum tube Cushion Part nos. for cylinders with built-in magnets In the case of cylinders with built-in magnets but no auto switches, do
Do not indicate lead wire length symbol N (none) for types D-A3, D-A44, D-G-39 or D-K39. Lead wire length symbols: 0.5m . Nil (Example) C73C 3m . L (Example) C73CL 5m . Z (Example) C73CZ None .
Because just one gateway unit controls up to 4 branch lines, it offers much more freedom in choosing valve mounting locations than do conventional serial units. Manifolds and input blocks can be mounted in close proximity of actuators, thus effectively shortening air piping and electrical wiring lengths.
Model: 4 (SGC400), Valve Type: 1 (Normally Closed), Seal Material: A (NBR), Pressure Range: 05 (0 to 0.5 MPa), Thread: N (NPT), Port Size: 25 (1), Pilot Valve: Y (0.35 W Type, V116), Voltage: 3 (110 VAC (115 VAC) 50/60 Hz), Electrical Entry: DO (DIN Terminal Without Connector)
Model: 4 (SGC400), Valve Type: 1 (Normally Closed), Seal Material: A (NBR), Pressure Range: 05 (0 to 0.5 MPa), Thread: N (NPT), Port Size: 25 (1), Pilot Valve: Y (0.35 W Type, V116), Voltage: 3 (110 VAC (115 VAC) 50/60 Hz), Electrical Entry: DO (DIN Terminal Without Connector), Surge Suppressor: None, Manual Override: Non-locking Push Type, Bracket Mounting Position: Without Bracket, Auto
Model: 3 (SGC300), Valve Type: 1 (Normally Closed), Seal Material: B (FKM), Pressure Range: 05 (0 to 0.5 MPa), Thread: Rc, Port Size: 20 (3/4), Pilot Valve: Y (0.35 W Type, V116), Voltage: 5 (24 VDC), Electrical Entry: DO (DIN Terminal Without Connector), Surge Suppressor: None, Manual Override: Non-locking Push Type, Bracket Mounting Position: B1 (Bracket on the Left Side)
Model: 4 (SGC400), Valve Type: 1 (Normally Closed), Seal Material: B (FKM), Pressure Range: 05 (0 to 0.5 MPa), Thread: Rc, Port Size: 25 (1), Pilot Valve: Y (0.35 W Type, V116), Voltage: 5 (24 VDC), Electrical Entry: DO (DIN Terminal Without Connector)
Model: 4 (SGC400), Valve Type: 1 (Normally Closed), Seal Material: A (NBR), Pressure Range: 05 (0 to 0.5 MPa), Thread: Rc, Port Size: 25 (1), Pilot Valve: Y (0.35 W Type, V116), Voltage: 5 (24 VDC), Electrical Entry: DO (DIN Terminal Without Connector)
Model: 2 (SGC200), Valve Type: 1 (Normally Closed), Seal Material: A (NBR), Pressure Range: 05 (0 to 0.5 MPa), Thread: N (NPT), Port Size: 10 (3/8), Pilot Valve: Y (0.35 W Type, V116), Voltage: 5 (24 VDC), Electrical Entry: DO (DIN Terminal Without Connector), Surge Suppressor: None, Manual Override: D (Push-turn Locking Lever Type), Bracket Mounting Position: Without Bracket, Auto Switch
Model: 2 (SGC200), Valve Type: 2 (Normally Open), Seal Material: A (NBR), Pressure Range: 05 (0 to 0.5 MPa), Thread: Rc, Port Size: 15 (1/2), Pilot Valve: Y (0.35 W Type, V116), Voltage: 1 (100 VAC 50/60 Hz), Electrical Entry: DO (DIN Terminal Without Connector), Surge Suppressor: None, Manual Override: Non-locking Push Type, Bracket Mounting Position: B1 (Bracket on the Left Side)
Model: 2 (SGC200), Valve Type: 1 (Normally Closed), Seal Material: A (NBR), Pressure Range: 05 (0 to 0.5 MPa), Thread: Rc, Port Size: 15 (1/2), Pilot Valve: Y (0.35 W Type, V116), Voltage: 5 (24 VDC), Electrical Entry: DO (DIN Terminal Without Connector)