Function: Normally Closed, Piping: Body Ported, Body Option: Large Flow Style, Voltage: 24VDC, Lead Wire: L Plug Connector w/Lead Wire 0.3m, Surge Suppressor: Light & Surge Suppressor, Manual Override: Non-locking Push Style, Port Size: Base Mounted w/Sub-plate/Body Ported Mfld M3X0.5, Option: -
Function: Normally Closed, Piping: Base Mounted, Body Option: Large Flow Style, Voltage: 24VDC, Lead Wire: L Plug Connector w/Lead Wire 0.3m, Surge Suppressor: Light & Surge Suppressor, Manual Override: Non-locking Push Style, Port Size: Base Mounted w/Sub-plate/Body Ported Mfld M3X0.5, Option: -
EX9-OEx_PE.eng Before Use Fieldbus device EX9-OET / OEP Series (Output block) EX9-PE Series (Power block) Summary of Product parts 1. EX9-OET1/EX9-OET2/EX9-OEP1/EX9-OEP2 2 Element Description No. 1 Output connector 1 Connects with output device. 2 Indicator LED Indicates the output status. Thank you for purchasing an SMC Fieldbus device.
Table 3.2-1 Amount of radiation and required ventilation Required ventilation amount (m3/min) Heat Differential temp. of Differential temp. of Model radiation 3 oC between inside and 6 oC between inside and (kW) outside of installation outside of installation area area HRS400-A-46Approx.52 865 435 Installation environment specifications Sound noise: HRS400-A-46 : 71 dB(A) Front 1m, height
View A PE L1 L2 L3 power supply cable Fig. 3-9 Wiring of power supply cable * Connect an over current protection to the power cable connected to the equipment to avoid hazard. 3.3 Installation HRL Series 3-16 HRX-OM-W060 Chapter 3 Transport and Setting Up 3.3.4 Contact input/output communicatin wiring Be sure to lock out and tag out the breaker of the facility power supply (the users machine
Attach the included filter cover and air filter (hook the protruding part of the filter cover on the product) and tighten screws to the required torque (M3: 0.63Nm). [] key (UP key) Increases set data. [MODE] key Used to change screens and modes.
( AN R ) 1,000 1,000 ISOclass4 ISOclass4 100 100 30/mi n( AN R ) 10 10 70/mi n( AN R ) 1 1 0 0.1 0.2 0.3 0.4 0.5 0.6 0 0.1 0.2 0.3 0.4 0.5 0.6 Particl diameter[m] Particl diameter[m] 4 - 11-LEJS63* Speed 600mm/sec Speed 1200mm/sec 100,000,000 100,000,000 ISOclass7 10,000,000 10,000,000 ISOclass8 ISOclass8 ISOclass6 1,000,000 1,000,000 ISOclass7 0/mi n(ANR) Particl concentration[Particls/m3
Connection of fittings When screwing fittings into valves, tighten as follows. (1) Follow the procedures below when installing an SMC fitting, etc. 1) M3 types After tightening the fitting by hand, use a wrench to tighten the fitting an additional approximately 1/4 turn. As a reference value, tightening torque is 0.4 to 0.5Nm.
Connection of fittings When screwing fittings into valves, tighten as follows. (1) Follow the procedures below when installing an SMC fitting, etc. 1) M3 types After tightening the fitting by hand, use a wrench to tighten the fitting an additional approximately 1/4 turn.
Stations: 08 (Stations), Wiring: F (D-sub Connector), Manifold Options: without Option, Exhaust: Q (Vacuum Pump System), Pressure Switch for Vacuum/Pressure Sensor: C (Digital Pressure Switch for Vacuum, 0 to -101, PNP 2 Outputs, with Unit Selection Function), Leadwire: Y (2m Switch/Sensor Only), Unit Options: C [Vacuum Pump System PE Port Female Thread Specification (M3)], 1st Nominal Nozzle
Stations: 10 (Stations), Wiring: F (D-sub Connector), Manifold Options: without Option, Exhaust: Q (Vacuum Pump System), Pressure Switch for Vacuum/Pressure Sensor: C (Digital Pressure Switch for Vacuum, 0 to -101, PNP 2 Outputs, with Unit Selection Function), Leadwire: Y (2m Switch/Sensor Only), Unit Options: C [Vacuum Pump System PE Port Female Thread Specification (M3)], 1st Nominal Nozzle
Terminal width 9.9mm PE L3 L2 L1 24 23 6 5 22 21 Remote Error signal Power supply RUN signal Ground operation (to be connected to the user's equipment) IDF190/ 240D-9-V 1) Remove the left panels. 2) Insert the cable through the rubber grommet. Remove the transducer cover, then connect the cable to the power supply transducer depending on the rated voltage.
(Tightening torque: 1.0 Nm) Terminal width 9.9mm PE L3 L2 L1 24 23 6 5 22 21 Remote operation Error signal Ground RUN signal Power supply (to be connected to the user's equipment) IDF190D/240D Series 3.2Installation 3-5 IDX-OM-Y002 Chapter 3 Transportation and installation 4) Mount the front panel back. [Remote control] Voltage of AC200V is present on the terminal block.
Connection of fittings When screwing fittings into valves, tighten as follows. (1) Follow the procedures below when installing an SMC fitting, etc. 1) M3 types After tightening the fitting by hand, use a wrench to tighten the fitting an additional approximately 1/4 turn.
Specification (M3)], 1st Nominal Nozzle Size: 0 (for Vacuum Pump System), 1st Selection Supply Valve and Release Valve: R ( Self-holding Release Valve Linked/N.C.), 1st Selection Vacuum V Port: 8 (Vacuum, V Port: Ø8), 1st Selection Quantity: 5
Thread Specification (M3)], 1st Nominal Nozzle Size: 0 (for Vacuum Pump System), 1st Selection Supply Valve and Release Valve: R ( Self-holding Release Valve Linked/N.C.), 1st Selection Vacuum V Port: 8 (Vacuum, V Port: Ø8), 1st Selection Quantity: 5
Stations: 10 (Stations), Wiring: L (Individual Wiring or None), Manifold Options: without Option, Exhaust: Q (Vacuum Pump System), Pressure Switch for Vacuum/Pressure Sensor: A (Digital Pressure Switch for Vacuum, 0 to -101, NPN 2 Outputs, with Unit Selection Function), Leadwire: L (Standard Leadwires, X2), Unit Options: C [Vacuum Pump System PE Port Female Thread Specification (M3)], 1st
Stations: Stations, Wiring: D-sub Connector, Manifold Options: without Option, Exhaust: Vacuum Pump System, Pressure Switch for Vacuum/Pressure Sensor: Digital Pressure Switch for Vacuum, 0 to -101, PNP 2 Outputs, with Unit Selection Function, Leadwire: 2m Switch/Sensor Only, Unit Options: C [Vacuum Pump System PE Port Female Thread Specification (M3)], 1st Nominal Nozzle Size: for Vacuum
Stations: Stations, Wiring: D-sub Connector, Manifold Options: without Option, Exhaust: Vacuum Pump System, Pressure Switch for Vacuum/Pressure Sensor: Digital Pressure Switch for Vacuum, 0 to -101, PNP 2 Outputs, with Unit Selection Function, Leadwire: 2m Switch/Sensor Only, Unit Options: C [Vacuum Pump System PE Port Female Thread Specification (M3)], 1st Nominal Nozzle Size: for Vacuum
Actuation: 1 (Normally Closed), Piping: 4 (Standard, Base Mounted), Voltage: 5 (24 VDC), Electrical Entry: L (L Plug Connector, w/Lead Wire Length 300 mm), Light/Surge Voltage Suppressor: Z (w/Light/Surge Voltage Suppressor, Manual Override: Non-locking Push Type, Port Size: M3 (Standard, Body Ported; Standard Base Mounted, w/Sub Plate)